Lab.gruppen PLM series Quick Start Manual

Also see for PLM 10000Q: Supplementary guide User manual addendum Specifications Quick start Technical data

Lab.gruppen PLM series Quick Start Manual Manual pdf 28 page image

28 PLM Series Quick Start and Field Reference Guide rev 1.0.68. Technical Specifications8. Technical SpecificationsL A B . G R U P P E N A B ▸ S W E D E NI N T E R N A T I O N A L C O N T A C T ▸ I N F O @ L A B G R U P P E N . C O M | U S C O N T A C T ▸ I N F O @ T C G-A M E R I C A S . C O MW W W . L A B G R U P P E N . C O M Item no. TDS-PLM14000_V3GeneralNumber of input channels 2Number of output channels 2Peak total output all channels driven 14000 WMax. Peak output voltage per channel 193 VMax. output current per channel 90 A peakMax. Output Power 2 ohms 4 ohms 8 ohms 16 ohmsAll channels driven 7000 W 4300 W 2300 W 1150 WChannel A, while channel B is driven at -3dB 2) 7500 W 4400 W 2300 W 1150 WAll channels driven into optimal impedance interval > 7000 W into 1.8 – 2.1 ohmsAudio PerformanceTHD + N 20 Hz - 20 kHz for 1 W <0.05%THD + N at 1 kHz and 1 dB below clipping <0.04%Dynamic range with digital inputs (for all supported sample rates) >114 dBDynamic range with analog inputs >112 dBFrequency response (1 W into 8 ohms, 20 Hz - 20 kHz) + /-0.05 dBInput Common Mode Rejection (CMR) 20 Hz to 1 khz >78 dBInternal sample rate 96 kInternal data path 32 bit fl oating pointProduct propagation delay, best case (96 kHz AES) 1.61 msProduct propagation delay, analog input 1.68 msSample Rate ConvertersTHD + Noise 0.00003 %, 20 Hz - 20 kHz, unweightedAnalog to Digital inputsTHD + Noise 0.00022 %, typical at 1 kHz unweighted at +26 dBu headroom setting0.00033 %, typical at 20 Hz and 20 kHz unweighted at +26 dBu headroom settingAES / EBU inputsSupported resolutions ≤24 bitSupported sample rates 44.1, 48, 88.2, 96, 176.4, 192 kHzDante Audio NetworkSupports redundant paths YesFlexible topology YesNetwork latency 0.8, 1.3 and 4 msDevice presetsLocal memory locations for the settings of the product 100LimitersAdjustable Inter-Sample Voltage Peak Limiter (ISVPL) 17.8 - 193 V, step size 0.1 VCurrent Peak Limiter < 300 ms 90 A peakCurrent Average Limiter (CAL) > 300 ms 44 ArmsLimiterMax (rms and peak limiters)– MaxRMS (rms voltage limiter) Yes– MaxPeak (peak voltage limiter) YesGainAmplifier gain 22 - 44 dB, step size 0.1 dBAnalog attenuator -Inf to 0 dB, step size 0.25 dBBack panel interfaceAES / EBU / I/O (input + link) 2 x 3-pin XLRAnalog, 2-channel I/O (input + link) 4 x 3-pin XLR, electronically balancedOutput connectors Neutrik Speakon (2 x NLT4) or 4 Binding Posts (pairs) (must be specified upon order)Auto 10/100, Auto Uplink 2 x RJ45 EtherCon Auto 10/100, Auto UplinkControl and monitoring interface Via Ethernet for Lake Controller softwareDetachable mains cord Neutrik PowerCon 32 ACooling Two fans, front-to-rear airflow, temperature controlled speedFront-panel user interface:Display, daylight readable LCD 2.5 inchFault/Warning/Limit/Clip indicators RGB LEDsMute and soft function buttons 8 providedStandby Power button On/OffMute Enable button Enables muting of outputs and inputs via soft-button keypadMeter button Toggles through meter viewsMenu button Provides a menu driven interface for full function front panel controlRotary Encoder YesExit button Provides a “back” functionPowerOperating voltage, 230 V / 115 V nominal 1) 140-265 V / 70-135 V (45 - 66 Hz)Soft start / Inrush Current Draw Yes / max. 5 AMains Power Average Limiter (PAL) YesDimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 470 mm (18.5”) deep including handles and rear support.Weight 13.5 kg (30 lbs.)Finish Black painted steel chassis with black painted steel / aluminum frontApprovals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCCNote 1): Separate 230 V or 115 V versions available. Not selectable on the product.Note 2): Assymetrically loading the output channels (as shown, for example): If one channel has reduced output power requirements, the voltage drop from the power supply will be reduced,resulting in a higher voltage and power output for the other channel.All specifications are subject to change without notice.Intercooler, Class TD and Lake are national and/or international registered trademarks of Lab.gruppen AB. PLM, Powered Loudspeaker Management, R.SMPS, LoadLibrary, LoadSmart,SpeakerSafe and ISVPL are trademarks of Lab.gruppen AB. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. Contour, Mesa Quad EQ, Mesa Parametric EQ, RaisedCosine Equalization, LimiterMax and Iso-Float are trademarks of Dolby Laboratories. Audinate is a registered trademark of Audinate Pty Ltd. Dante and Zen are trademarks of Audinate Pty Ltd.Allother trademarks remain the property of their respective owners.Copyright © 2009 Lab.gruppen AB.All rights reserved.PLM 14000