Rev. 1.0.4Item no. UM-PLM-DLC-ADDDolby® Lake® Controller User Manual PLM™ Edition AddendumPLM SeriesPowered Loudspeaker Management™ systems

impOrTaNT

WELCOmE

sOfTWarE iNsTaLLaTiON

Moving user files between installations

rEfErENCE

OpEraTiON

Status Tab

Attenuation

Mute and polarity enable

Control Tab

Amplifier clip level

Ambient Temperature

LoadSmart Results

Voice Coil Temperature

History tab

Peak/Average

Events Tab

Global Control Tab

Global Events Tab

Sorting options

Lab.gruppen PLM Series PLM 10000Q User Manual Addendum

PLM 10000Q

AppROVALS

user Responsibility

WELCOME

INSTALLATION

Cooling

operating Voltage

QUICK START TUTORIAL

How to Configure the PLM

Gain Settings

Gain / Level optimization

CONTROLS ANd CONNECTIONS

Rear Panel

network connectors

TEChNICAL SpECIfICATIONS

WARRANTy

APPROVALs

User responsibility

Dolby ® Lake ® Processing and Controller

INsTALLATION

Operating voltage

Front Panel overview

Rear Panel overview

Network connectors

Integrated Dolby Lake Processing

OPERATION AND PERFORMANCE

Amplifier and Load Protection Systems

Current Peak Limiter (CPL)

Short circuit protection

sIGNAL FLOW AND PROCEssING

Loudspeaker processor configuration

Modules and Frames

Super Modules

FRONT PANEL INTERFACE

Key Lock Front Panel

Network activity LED

Exit button

Module Output Mute

LED Faults, Warnings and Clip indications

Green indications

Meter Mode

Meter view 1 – Home View

Meter View 3 – Temperature View

Menu Mode

Module submenu

Inter-Sample Voltage Peak Limiter (ISVPL)

Input Routing and Settings submenu

IsoFloat

Attenuation submenu

Latency ('Inh. Latency')

IP Address

LoadSmart

Dante

bACk PANEL INTERFACE

Iso-Float electronic balancing

Speaker Output Connections

Binding Post Output Connectors

APPENDIX

Maintenance

APPLICATION GUIDE

Gain Structure

Speaker configurations

Interconnecting digital audio

Accessories

Firmware Upgrades

Firmware Upgrades Using the Dolby Lake Controller PLM Edition

Hot swapping PLM devices

TECHNICAL sPECIFICATIONs

WARRANTY

Dante ™ audio network

Operating Voltage

Power Supply

Loudspeaker Processor Configuration

Network Activity LED

Soft Function Buttons

Warning and Fault Indications

Firmware version ('FW version')

Configure # of cabinets in parallel

Using the PLM as a "break-in box

PowerCon® wiring details

Binding Post output connectors

Current Draw and Thermal Dissipation Specifications

Glossary of Terms, Acronyms and Abbreviations

I/O Panels

Speaker Configurations

Digital Clock Configuration

INTRODUCTION

PLM SERIES aND DaNTE ™ NETwORkINg FEaTURES

aVOIDINg SINgLE POINT OF FaILURE (SPF) ISSUES

Signal type redundancy

NETwORk CONNECTIONS aND TOPOLOgIES

Star or Hub-and-Spoke networks

Dual daisy-chained switches

PLM / Dante Network Size Limitations

Wireless Network Topologies

NETwORk HaRDwaRE RECOMMENDaTIONS

Recommended network cabling: Belden ® 1305A

REFERENCES aND DEFINITIONS

aDDITIONaL INFORMaTION

Approvals

Important Safety Instructions

Radio interference

Welcome

Lab.gruppen documents

Installation

Grounding

Quick Start Tutorial

Software and Firmware Updates

Networked Applications

Gain / Level Optimization

quick guide overview

Quick Guide Overview

Rear Panel Overview

Input connectors and Links

Output connectors

Technical Specifications

Warranty

Lake ® Processing and Controller

AC input

Operation and Performance

Power over time

Current Average Limiter (CAL ™ )

VHF protection

Signal Flow and Processing

Mute points

loudspeaker processor configuration

Presets

Front Panel Interface

Pinging modules in the Lake Controller software from the PLM

Power Button

Exit Button

Mute functions

PLM Input Mute

Power Output Mute

Meter View 2 – Module View

Meter View 4 – Input View

Menu View

Phase reverse

Inter-Sample Voltage Peak Limiter Threshold (ISVPL Threshold)

MaxRMS Release (MaxRMSRel)

Input selection and sensitivity settings

Iso-Float

Frame submenu

Frame Info

Max Output Voltage ('MaxOutVolt')

Dimming

LoadSmart verification

Back Panel Interface

Unbalanced operation

Digital inputs and links

Binding post output connectors

Appendix

Application Guide

System Latency and Delay Compensation

Cable types and distance limitations

Passive splitters

Firmware upgrades using the update utility

Firmware upgrades using the Lake Controller software

Hot Swapping PLM devices

important safety instructions

user responsibility

main features

lake analyzer bridge

additional documentation

rear mounting

operating voltage

product overview

Meter Button

back panel overview

input and link connectors

operation and performance

asymmetrical power

amplifier and load protection systems

temperature protection

vhf protection

short circuit protection

signal flow and lake processing


Contents Table Of Contents Table Of Contents impOrTaNT WELCOmE sOfTWarE iNsTaLLaTiON Moving user files between installations rEfErENCE OpEraTiON Status Tab Attenuation Mute and polarity enable Control Tab Amplifier clip level Ambient Temperature LoadSmart Results Voice Coil Temperature History tab Peak/Average Events Tab Global Control Tab Global Events Tab Sorting options	Rev. 1.0.4Item no. UM-PLM-DLC-ADDDolby® Lake® Controller User Manual PLM™ Edition AddendumPLM SeriesPowered Loudspeaker Management™ systems Next / 25