Contents - contact information
- Table Of Contents
- Table Of Contents
- Introduction
- How an Inverter/Charger Works
- Standard Features and Benefi ts
- Figure 3, Top and Left Side Features
- Figure 4, Front and Back Side Features
- Battery Temperature Sensor
- Installation
- Figure 6, MMS1012 Model Basic Installation Diagram
- Figure 7, MMS1012-G Model Basic Installation Diagram
- Locating and Mounting the Inverter
- Figure 9, MMS1012 Model Inverter/Charger Dimensions
- Wiring Guidelines
- DC Wiring
- DC Overcurrent Protection
- DC Grounding
- DC Cable Connections
- Battery Bank Wiring
- DC Ground Wire
- AC Wiring
- AC Wiring Connections
- AC Input Wiring
- Figure 13, AC Wiring Connections (MMS1012 model)
- AC Output Wiring
- Functional Test
- Operation
- Standby Mode
- Figure 15, Automatic 4-Stage Charging Graph
- Figure 16, BTS Temperature to Charge Voltage Change
- Protection Circuitry Operation
- Inverter Start-up
- Factory Default Settings
- Table 6, Inverter/Charger Default Settings
- Maintenance and Troubleshooting
- Resetting the Inverter
- Table 7, Troubleshooting Guide
- Table 8, MMS Series Specifi cations
- Appendix A - Optional Equipment and Accessories
- Figure 18, Series Battery Wiring
- Series-Parallel Wiring
- Figure 21, Battery Bank Wiring Examples (12-volt)
- limited warranty
- How to Receive Repair Service
|
© 2010 Magnum Energy, Inc.5.0 Specifications39Table 8, MMS Series Specifications5.0 SpecificationsMODEL MMS1012 MMS1012-GInverter SpecificationsInput battery voltage 9 to 16 VDCNominal AC output voltage 120 VAC +/- 5%Output frequency and accuracy 60 Hz +/- 0.1 Hz1msec surge current (amps AC) 38100msec surge current (amps AC) 215 sec surge power (real watts) 175030 sec surge power (real watts) 16005 min surge power (real watts) 120030 min surge power (real watts) 1050Continuous power output at 25° C 1000 VAMaximum continuous input current 133 ADCInverter efficiency (peak) 0.87Transfer time 16 msecsAC transfer capability 15ASearch mode (typical) 5 wattsNo load (120 VAC output, typical) 19 wattsWaveform Pure Sine WaveCharger SpecificationsContinuous output at 25° C 50 ADCCharger efficiency 84%Power factor > 0.95Input current at rated output (amps AC) 7Battery temperature compensation Yes, 15 ft Battery Temp Sensor standardGeneral Features and CapabilitiesProtection circuitry Low/High Battery, Over-temp & OverloadCorrosion protection PCB’s conformal coated, powder coated chassisAC Output Hardwire GFCI outletAC Input Hardwire 3 ft cordOutput circuit breaker 15AInput circuit breaker 20 AACInternal cooling Yes, 0 to 59 cfm variable speedOptional remotes available MM-RC or ME-RC50UL listing ETL listed to UL/cUL458, CSA C22.2 #107.1,meets KKK-A-1822E std.Environmental SpecificationsOperating temperature -20° C to +60° C (-4° F to 140° F)Non-operating temperature -40° C to +70° C (-40° F to 158° F)Operating humidity 0 to 95% RH non-condensingPhysical SpecificationsDimensions (L x W x H) 16.6”x 8.4”x 4.7” (42cm x 21cm x 12cm)Mounting Shelf or wall (no vents facing downward)Weight 23 lbs. (10.4 kg)Shipping weight 25 lbs. (11.3 kg)Specifications @ 25° C - Subject to change without notice
PreviousNext |