Makita 2012NB Instruction Manual
Also see for 2012NB: Instruction manualInstruction manualInstruction manualInstruction manualInstruction manual
                                                    |
4ENGLISH (Original instructions)Explanation of general view1-1. Carrying handle1-2. Sub-table1-3. Carrying handle2-1. Bolt or screw3-1. Pilot lamp3-2. Switch4-1. Crank handle4-2. Scale4-3. Main frame4-4. Indicator plate5-1. Depth gauge6-1. Crank handle6-2. Groove6-3. Depth adjusting gauge7-1. Stopper7-2. Stopper button7-3. Stopper knob7-4. Table top8-1. Lock plate8-2. Pulley8-3. Drum8-4. Chain8-5. Thumb screw9-1. Blade installation bolts9-2. Set plate9-3. Magnetic holder9-4. Drum9-5. Blade9-6. Claw10-1. Socket wrench10-2. Magnetic holders11-1. Socket wrench11-2. Lock plate11-3. Blade installation bolt12-1. Set plate13-1. Magnetic holder13-2. Set plate13-3. Blade14-1. Blade installation bolts14-2. Set plate14-3. Magnetic holder14-4. Drum14-5. Blade14-6. Claw15-1. Socket wrench15-2. Magnetic holders16-1. Screw16-2. Set plate16-3. Blade16-4. Blade gauge17-1. Set plate17-2. Groove17-3. Blade17-4. Drum18-1. Socket wrench18-2. Lock plate18-3. Blade installation bolt19-1. Hood set20-1. Thumb screw20-2. Chip cover20-3. Chain20-4. Hood set23-1. Ruler23-2. Post card23-3. Adjusting screw24-1. Hex wrench25-1. Limit mark26-1. Brush holder cap26-2. Screwdriver27-1. Column27-2. Screw27-3. Chain28-1. Base28-2. Blade28-3. More than 4 mmSPECIFICATIONSModel 2012NBCutting width 304 mm3.0 mm of stock width less than 150 mm1.5 mm of stock width from 150 mm to 240 mmMax. cutting depth1.0 mm of stock width from 240 mm to 304 mmFeed rate (min-1) 8.5 mTable size (W x L) 304 mm x 771 mmNo load speed (min-1) 8,500Overall length (W x L x H) 483 mm x 771 mm x 401 mmNet weight 28.1 kgsafety class /II Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Specifications may differ from country to country. Weight according to EPTA-Procedure 01/2003ENE001-1Intended useThe tool is intended for planing wood. ENF002-1Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, and canonly be operated on single-phase AC supply. They aredouble-insulated in accordance with European Standardand can, therefore, also be used from sockets withoutearth wire.ENF100-1For public low-voltage distribution systems ofbetween 220 V and 250 V.Switching operations of electric apparatus cause voltagefluctuations. The operation of this device underunfavorable mains conditions can have adverse effectsto the operation of other equipment. With a mainsimpedance equal or less than 0.38 Ohms it can bepresumed that there will be no negative effects. Themains socket used for this device must be protected witha fuse or protective circuit breaker having slow tripping |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine