Makita DLS714 Instruction Manual

Also see for DLS714: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

19 ENGLISHWARNING: If the ring is needed to mount theblade onto the spindle, always be sure that thecorrect ring for the blade's arbor hole you intendto use is installed between the inner and the outerflanges. Use of the incorrect arbor hole ring mayresult in the improper mounting of the blade causingblade movement and severe vibration resulting inpossible loss of control during operation and in seri-ous personal injury.For tool with the inner flange forother than 20 mm or 15.88 mm hole-diameter saw bladeCountry specificThe inner flange has a certain diameter of a blademounting part on one side of it and a different diameterof blade mounting part on the other side. Choose acorrect side on which blade mounting part fits into thesaw blade hole perfectly.► Fig.36: 1. Outer flange 2. Saw blade 3. Inner flange4. Hex socket bolt (left-handed) 5. Spindle6. Blade mounting partCAUTION: Make sure that the blade mountingpart "a" on the inner flange that is positionedoutside fits into the saw blade hole "a" perfectly.Mounting the blade on the wrong side can result inthe dangerous vibration.Dust bagOptional accessoryThe use of the dust bag makes cutting operationscleaner and dust collection easier.To attach the dust bag, fit it onto the dust nozzle.To attach the fastener, align the top end of the fastenerwith the triangular mark on the dust bag.When the dust bag is about half full, remove the dustbag from the tool and pull the fastener out. Emptythe dust bag of its contents, tapping it lightly so as toremove particles adhering to the insides which mighthamper further collection.► Fig.37: 1. Dust bag 2. Dust nozzle 3. FastenerNOTE: If you connect a vacuum cleaner to your saw,cleaner operations can be performed.Securing workpieceWARNING: It is extremely important to alwayssecure the workpiece correctly with the propertype of vise. Failure to do so may result in seriouspersonal injury and cause damage to the tool and/orthe workpiece.WARNING: When cutting a workpiece thatis longer than the support base of the saw, sup-port the entire length of the material beyond thesupport base and at the same height to keep thematerial level. Proper workpiece support helps toavoid blade pinch and possible kickback which mayresult in serious personal injury. Do not rely solely onthe vertical vise and/or horizontal vise to secure theworkpiece. Thin material tends to sag. Support work-piece over its entire length to avoid blade pinch andpossible KICKBACK.► Fig.38: 1. Support 2. Turn baseVertical viseWARNING: Secure the workpiece firmlyagainst the turn base and guide fence with thevise during all operations. Otherwise the materialmay move during the cutting operation, cause dam-age to the blade, and be thrown which may result inloss of control and serious personal injury.Install the vertical vise on either the left or right side ofthe guide fence or the holder assembly (optional acces-sory). Insert the vise rod into the hole in the guide fenceor the holder assembly and tighten the lower screw tosecure the vise rod.► Fig.39: 1. Vise arm 2. Vise rod 3. Guide fence4. Holder 5. Holder assembly 6. Vise knob7. Lower screw 8. Upper screwPosition the vise arm according to the thickness andshape of the workpiece and secure the vise arm bytightening the upper screw. If the upper screw contactsthe guide fence, install the upper screw on the oppositeside of vise arm. Make sure that no part of the toolcontacts the vise when lowering the handle fully andpulling or pushing the carriage all the way. If some partcontacts the vise, re-position the vise.Press the workpiece flat against the guide fence and theturn base. Position the workpiece at the desired cuttingposition and secure it firmly by tightening the vise knob.Horizontal viseOptional accessoryWARNING: Grip the workpiece only when theindicator is at the topmost position. Failure to doso may result in insufficient securing of the workpiece.This may cause the workpiece to be thrown, causedamage to the blade or cause the loss of control,which may result in personal injury.► Fig.40: 1. Vise knob 2. Indicator 3. Vise shaft4. BaseThe horizontal vise can be installed on the left side ofthe base.

/ 164

Related manuals for Makita DLS714

Makita DLS714 Instruction Manual

This manual is suitable for:

DLS714

manualsdatabase

Your AI-powered manual search engine