Makita LS0714 Instruction Manual
Also see for LS0714: Instruction manualInstruction manualInstruction manualParts BreakdownInstruction manual
                                                                                                                    | |
16clockwise and counterclockwise to seat the turnbase in the 0° miter notch. (Leave as it is if thepointer does not point to 0°.) Loosen the hex boltssecuring the guide fence using the socket wrench.Lower the handle fully and lock it in the loweredposition by pushing in the stopper pin. Square theside of the blade with the face of the guide fenceusing a triangular rule, try-square, etc. Thensecurely tighten the hex bolts on the guide fence inthe order from the right side.Fig.46Make sure that the pointer points to 0° on the miterscale. If the pointer does not point to 0°, loosen thescrew which secures the pointer and adjust thepointer so that it will point to 0°.Fig.472. Bevel angle(1) 0° bevel anglePush the carriage toward the guide fence andtighten two clamp screws to secure thecarriage. Lower the handle fully and lock it inthe lowered position by pushing in thestopper pin. Loosen the lever at the rear ofthe tool.Turn the 0° bevel angle adjusting bolt (lowerbolt) on the right side of the arm two or threerevolutions counterclockwise to tilt the bladeto the right.Fig.48Carefully square the side of the blade withthe top surface of the turn base using thetriangular rule, try-square, etc. by turning the0° bevel angle adjusting bolt clockwise. Thentighten the lever securely.Fig.49Make sure that the pointer on the arm point to0° on the bevel scale on the arm holder. If itdoes not point to 0°, loosen the screw whichsecures the pointer and adjust the pointer sothat it will point to 0°.Fig.50(2) 45° bevel angleFig.51Adjust the 45° bevel angle only afterperforming 0° bevel angle adjustment. Toadjust left 45° bevel angle, loosen the leverand tilt the blade to the left fully. Make surethat the pointer on the arm points to 45° onthe bevel scale on the arm holder. If thepointer does not point to 45°, turn the 45°bevel angle adjusting bolt (upper bolt) on theright side of the arm until the pointer points to45°.Adjusting the position of laser lineFor model LS0714FL, LS0714LFig.52Fig.53WARNING:• As the tool is plugged when adjusting the positionof laser line, take a full caution especially at switchaction. Pulling the switch trigger accidentally causean accidental start of the tool and personal injury.CAUTION:• Never look into the laser beam directly. Direct laserbeam causes damage to your eyes.• Never apply a blow or impact to the tool. A blow orimpact causes the incorrect position of laser line,damage to the laser beam emitting part or a shortlife of the tool.• Have the tool repaired by Makita authorizedservice center for any failure on the laser unit. Nochange with different type of laser is permitted.When adjusting the laser line appears on the leftside of the saw blade1 234 5005527When adjusting the laser line appears on the rightside of the saw blade1 2 3005528For both adjustments, do as follows.1. Make sure that the tool is unplugged.2. Draw the cutting line on the workpiece and place iton the turn table. At this time, do not secure the1. Screw to change the movable range of the adjustingscrew2. Adjusting screw3. Hex wrench4. Laser line5. Saw blade1. Screw to change the movable range of the adjustingscrew2. Saw blade3. Laser line |
Related manuals for Makita LS0714
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
Makita LS0714 Instruction Manual
manualsdatabase
Your AI-powered manual search engine