Makita UA004G Instruction Manual

Also see for UA004G: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

14 ENGLISH19. Before cutting limbs, keep an escape areaaway from the falling limb. First, clearobstructs such as limbs and branches fromthe work area. Move all tools and goods fromthe escape area to another safe place.20. Before cutting branches and limbs, checkthe falling direction of them, considering thecondition of branches and limbs, adjoiningtrees, wind direction, etc. Pay full attention tothe falling direction, and the rebound of thebranch, which hit the ground.21. Never hold the tool at an angle of more than60°. Otherwise falling objects can hit the oper-ator and cause serious injury. Never standunderneath the limb being cut.22. Pay attention to broken or bent branches. Theymay bounce back in cutting, causing unexpectedinjury.23. Before cutting limbs that you intend to cut,remove branches and leaves around them.Otherwise the saw chain may be caught by them.24. To prevent the saw chain from being caught inthe kerf, do not release the lever before pullingthe saw chain out of the kerf.25. If the saw chain is bound in the kerf, immedi-ately stop the tool, carefully move the branchto open the kerf and release the saw chain.26. Avoid kickback (rotational reactive forcetowards the operator). To prevent kickback,never use the guide bar nose or perform apenetrating cut. Always beware of the positionof the guide bar nose.27. Check the chain tension frequently. Whenchecking or adjusting the chain tension,switch off the tool and remove the batterycartridge. If the tension is loose, tighten it.28. When you use the tool on muddy ground, wetslope, or slippery place, pay attention to yourfooting.29. Do not submerge the tool into a puddle.30. Do not leave the tool unattended outdoors inthe rain.Transport1. Before transporting the tool, switch off the tooland remove the battery cartridge. Always fitthe guide bar cover during transportation.2. When transporting the tool, carry it in a hori-zontal position by holding the grip.Maintenance1. Have your equipment serviced by our autho-rized service center, always using only genu-ine replacement parts. Incorrect repair and poormaintenance can shorten the life of the tool andincrease the risk of accidents.2. Before doing any maintenance or repair workor cleaning the tool, always switch off the tooland remove the battery cartridge. Wait until thetool cools down.3. Always wear protective gloves when handlingthe saw chain.4. After each use, tighten all screws and nuts,except for adjustment screws.5. Keep the saw chain sharp. If the saw chainhas become blunt and cutting performance ispoor, ask Makita authorized service center tosharpen it or replace it with new one.6. Do not attempt any maintenance or repairnot described in this instruction manual. AskMakita authorized service center for suchwork.7. Always use Makita genuine spare parts andaccessories only. Using parts or accessoriessupplied by a third party may result in the toolbreakdown, property damage and/or seriousinjury.Storage1. Before storing the tool, perform full cleaningand maintenance. Fit the guide bar cover.Remove the battery cartridge. Drain the chainoil after the tool cools down.2. Store the tool in a dry and high or locked loca-tion out of reach of children.3. Do not prop the tool against something, suchas a wall. Otherwise it may fall suddenly andcause an injury.4. When storing the tool, avoid direct sunlightand rain, and store it in a place where it doesnot get hot or humid.Electrical and battery safety1. Do not dispose of the battery(ies) in a fire.The cell may explode. Check with local codes forpossible special disposal instructions.2. Do not open or mutilate the battery(ies).Released electrolyte is corrosive and may causedamage to the eyes or skin. It may be toxic ifswallowed.3. Do not charge battery in rain, or in wetlocations.4. Do not charge the battery outdoors.5. Do not handle charger, including charger plug,and charger terminals with wet hands.6. Avoid dangerous environment. Don't use thetool in dump or wet locations or expose it torain. Water entering the tool will increase the riskof electric shock.7. Do not replace the battery in the rain.SAVE THESE INSTRUCTIONS.WARNING: DO NOT let comfort or familiaritywith product (gained from repeated use) replacestrict adherence to safety rules for the subjectproduct. MISUSE or failure to follow the safetyrules stated in this instruction manual may causeserious personal injury.Important safety instructions forbattery cartridge1. Before using battery cartridge, read all instruc-tions and cautionary markings on (1) batterycharger, (2) battery, and (3) product usingbattery.2. Do not disassemble or tamper with the batterycartridge. It may result in a fire, excessive heat,or explosion.