Makita WST05 Instruction Manual

Also see for WST05: Instruction manual Instruction manual

4ENGLISHModels:LS0714, LS0815, LS1013, LS1016, LS1017, LS1018, LS1019, LS1212, LS1214, LS1216, LS1219, LS1030N, LS1040,LS1220, LS1221, BLS713, DLS713, DLS714, DLS110, DLS111, DLS112, MT230, M243, MLS100, MLS101, M2300,LH1040, LH1200FL, LH1201FLInclusive of models followed by F, L and FL, if any.PreparationNote: Check contents of package for the following components. Please inform Makita service center of any part missing inthe package immediately.• Miter saw stand (1 unit)• Hex wrench 5 (1 pc.)• Hex wrench 6 (1 pc.)• Wrench 10-13 (1 pc.)• Wheel assembly (1 unit)– hex nut 8 (1 pc.), flat washer 8 (1 pc.), wheel (2 pcs.),flat washer 12 (3 pcs.), wheel axis (1 pc.)• Foot arm (1 unit)• Working table (2 units)• Front foot R (1 unit)• Front foot L (1 unit)• Hex socket bolt M6 x 40 (4 pcs.)• Hex socket bolt M8 x 10 (2 pcs.)• Flat washer 6 (4 pcs.)• Hex nut 6 (4 pcs.)• Support (1 pc.)• Hex bolt M8 x 50 (4 pcs.)• Hex nut 8 (4 pcs.)• Flat washer 8 (8 pcs.)• Screw plate (2 pcs.)Symbols............. Read instruction manual.............. Maximum allowable loadingCAUTION:• Read and thoroughly understand this manual and theinstruction manual of the tool you use beforeperforming the following.• Before installing a tool on this stand, always switch offand unplug the tool.• The stand should be bolted in a stable and levelsurface using the right angle brackets provided on twoof four feet.• Use only with Makita model indicated in the instructionmanual.• Use only the handle to avoid pinched fingers whenraising or folding the stand.• Before operating the tool, secure it to stand using bolts.• Do not use the stand on uneven or unstable surface.• Do not climb, sit or stand on the stand.• When setting up the miter saw stand in the uprightposition or folding it, be sure to securely keep pressingthe pipe of miter saw stand with your foot until it locks.• When storing miter saw stand, never lean it against thewall or the like lengthwise or sideways.• Never pull the locking lever without holding the handle.Assembling miter saw stand: (Fig. 1)(1) Front foot (2 units)1. Place the stand assembly upright.2. Secure the front foot R (11) to the stand leg withscrew plate (10), hex bolt M6 x 40 (9) (2 pcs), flatwasher 6 (12) (2 pcs) and hex nut 6 (13) (2 pcs).3. Insert the support (14) into the holes on the frontfoot R.4. Secure the front foot L (11-1) by repeating theabove procedure.(2) Wheel assembly1. Remove the whole parts from the wheel axis.2. Place the flat washer (4), wheel (3) and flat washer(4) on wheel axis (5) in order. Then slide the wheelaxis (5) into the leg (15). Place the flat washer (4),wheel (3) and flat washer (2) on the other side of thewheel axis. Secure the lever on the wheel axis end,and then tighten the hex nut 8 (1).3. Check the wheels turn properly after loosening thelever. If the wheels do not turn, it shows the hex nut 8is excessively tightened. When using a miter sawstand, secure the lever to fix the wheels.(3) Foot arm (1 unit)Insert the foot arm (7) into the ports of the leg andsecure them by hex socket bolt M8 x 10 (8) (2 pcs).When securing the foot arm, insert it in a properdirection. Otherwise the foot arm cannot be secured.(4) Working table (2 units)Slide the working tables (6) into the slots on the standand secure them to the desired position by the lever(16). The lever can be adjusted to a different angle bypicking the lever up and turning it at a desired angle.Installing miter saw on the miter sawstand: (Fig. 2)Loosen the levers (16). Place a miter saw so that the boltholes in the miter saw base overlap holes on the workingtable. Secure the miter saw stand with hex bolt M8 x 50(17) (4 pcs), flat washer 8 (18) (8 pcs) and hex nut 8 (19)(4 pcs). Secure the levers (16).Note: Use small holes in the working tables as scales toset the miter saw properly.Setting up: (Fig. 3)1. Hold down the handle (23) and place your foot on thesupport (14).2. Release the locking lever (22).3. Pull up the handle (23) with both hands until the redindicator passes the height level “2” or “3”.(220 lbs.)100KgMAX.