NAD T 765 Owner's Manual

Also see for T765: Catalog Specification sheet Manual Specifications Owner's manual

NAD T 765 Owner's Manual Manual pdf 40 page image

LEARNING CODES FROM OTHER REMOTESBegin by positioning the HTR 3 “nose-to-nose” with the source remote so the two devices’ infraredwindows are about 2 inches apart.• Enter Learning Mode: On the HTR 3, simultaneously press-and-hold for 3 seconds both a DeviceSelector key and the [RES] key (just below the DISP key) until the Learn LED at the center of theHTR 3 turns steady green.• Press the HTR 3’s function key you wish to teach a command; the Learn LED will turn amber.• Press-and-hold the function key on the source remote: The HTR 3’s Learn LED will flicker amber fora second or two, then turn solid green. The command is learned.• Press the HTR 3’s Device Selector key again to exit the learning mode.If the Learn LED does not flicker amber you may need to vary the distance between the remotes. Ifthe Learn LED turns red rather than green, that particular command of that source remote commandcould not be learned.Example: Learning “DVD Pause”Position the HTR 3 and your DVD player’s remote as described above.• On the HTR 3, simultaneously press-and-hold [DVD] and [RES]; the Learn LED turns steady green.• Press the HTR 3’s Pause [ ] key; the Learn LED turns amber.• Press-and-hold the corresponding Pause key of your DVD player’s remote control; the HTR 3’s LearnLED flickers amber and then turns solid green. The command is learned.• Press [DVD] again to exit the learning mode.CANCEL OPERATIONYou can cancel configuring a key, by pressing the active Device Selector key before the learn process iscomplete; the Learn LED will turn red.PUNCH THROUGHThe HTR 3’s “punch-through” function allows you to retain a function key from one Device Select “page”to another, so that, for example, the AMP [SURR MODE] function might still control the T 765 when theDVD Device Selector page is active.NOTEThe HTR 3’s [VOL] keys are pre-programmed as “punched-through” for all Device Select pages:[VOL] will operate the T 765’s master-volume regardless of the currently selected device. The [SURR][CENTER,] and [SUB] Channel Volume controls similarly are pre-programmed as punched-through.To set a punch through, after entering the Learning Mode, and pressing the desired key to be punchedthrough, simply press the device key twice of the device to punch through to. The status LED will turngreen; press the Device Selector key again to exit Learning Mode.Example: Punch-through AMP [SURR MODE] key to the DVD “page”• On the HTR 3, simultaneously press-and-hold [DVD] and [RES]; the Learn LED turns steady green.• Press [SURR MODE]; the Learn LED turns amber.• Press [AMP] twice; the Learn LED turns green.• Press [DVD] again to exit the learning mode.COPY A COMMAND FROM ANOTHER KEYYou may copy a command from any HTR 3 key to any other. To copy a key function, after entering theLearning Mode, and pressing the desired key to be copied to, simply press the device key from whichyou wish to copy, having first pressed its Device Selector key if it resides on another “page.” The statusLED will turn green; press the Device Selector key again to exit Learning Mode.Example: Copy the Pause command from the CD page to the AMP [ ] button:• On the HTR 3, simultaneously press-and-hold [AMP] and [RES]; the Learn LED turns steady green.• Press Pause [ ] ; the Learn LED turns amber.• Press [CD]; press Pause [ ] ; the Learn LED turns green.• Press [AMP] again to exit the learning mode.NOTEThe copy and punch-through functions are similar. However, if you copy a command and thensubsequently delete, or over-write the original (source-key) command , the copied-to key’scommand remains unchanged. If you punch-through to a command and then delete or over-writethe original key, the punched-through functions also change accordingly.OPERATIONUSING THE HTR 3 REMOTE CONTROL40ENGLISH