NAD T785 HD Owner's Manual

Also see for T785: Catalog Specification sheet Owner's manual Specifications Owner's manual

NAD T785 HD Owner's Manual Manual pdf 30 page image

DTS - ES™ MATRIX 6.1In this format, the additional signals of the back channel receive a matrixencoding and are inputted into the right and left surround channels.During reproduction they are decoded to the right, left and back surroundchannels.Since this bit-stream format is 100% compatible with conventional DTSsignals, the DTS-ES Matrix 6.1 format effect can also be achieved fromsources with DTS-ES 5.1 signals.Naturally, it is also possible to reproduce from a DTS 5.1 channel decoder,signals recorded in DTS-ES 6.1.When a DTS-ES decoder processes a discrete DTS-ES 6.1 or in Matrix 6.1,these formats are automatically detected and the Optimum Surroundmode is selected. However, some DTS-ES Matrix 6.1 sources may bedetected as DTS. In this case the DTS-ES Matrix mode should be selectedmanually in order to reproduce them.DTS NEO: 6™ SURROUNDThis mode applies the conventional 2-channel signals such as digital PCMor analog stereo signals to the high precision digital matrix decoder usedfor DTS-ES Matrix 6.1 to achieve 6.1-channel surround playback. DTS Neo: 6surround includes two modes for selecting the optimum decoding of thesignal sources:DTS NEO: 6 CINEMA : This method is ideal for the reproduction ofmovies. The decoding takes place by emphasizing the separation inorder to achieve the same atmosphere with 2-channel, as with 6.1-channel sources.DTS NEO: 6 MUSIC : Mainly recommended for music reproduction.The right and left front channels do not pass through the decoder andare reproduced directly so there is no loss in sound quality, and theeffects of the right surround, left surround, central and back surroundchannels add a natural sensation of expansion of the sound field.ENHANCED STEREOPlease refer to the same description of ‘ENHANCED STEREO’ under the‘LISTENING MODES’ segment of the ‘OPERATION - USING THE T 785 - MAINMENU’.DISPLAY SETUPThe Vacuum Fluorescent Display (VFD) and On-Screen Display (OSD) can beshown in various ways by navigating through the parameters at the ‘DisplaySetup’ menu. Use a combination of or ENTER and keys to stepthrough the ‘Display Setup’ menu items.NOTEThe configurations set forth at ‘Display Setup’ are carried over wheneverit is enabled during A/V Preset setting. Please see also the section belowabout ‘AV Presets.’VACUUM FLUORESCENT DISPLAY (VFD)Display : Select ‘On’ to display all applicable data or characters at theVFD. Nothing will be shown at VFD if ‘Temp’ is selected. At ‘Temp’ settinghowever, whenever any of the front panel controls or their correspondingkeys in the remote control is activated, the appropriate VFD characters willbe shown temporarily and then fade away. Note that if any of the Zonesare at powered state, they will be continually shown at VFD even at ‘Temp’setting.Dimmer : If it is desired to reduce the brightness of the VFD, set Dimmer to‘Dim’. Otherwise, select ‘Bright’ to return to normal VFD brightness.Line 1, Line 2 : The VFD shows two main lines of data or characters. Line2 is the line of data or characters located at the lower bottom of the VFDwhile directly above it is Line 1. For both lines, one can select which displaycould be shown by choosing through the followingMain Source : Shows the active Source.Volume : Current Volume level is shown.Listening Mode : Selected Listening Mode is shown.Audio Src Format : Shows the active Source’s detected audio format.Audio Codec: Displays the detected audio stream format like Analog,PCM Surround, Dolby TrueHD, DTS-HD Master Audio and other formats.Video Mode: Show the video resolution of the active input source.Details shown include the video resolution with frame rate. For a betterunderstanding of these video details, consult with your NAD AudioSpecialist or your distributor’s technical department.Zone 2-Zone 3-Zone 4 Source : The assigned Source for theapplicable Zone is shown.Off : Select ‘Off’ if it is desired not to show any data at the applicable Line.Temp Line : Choose between Line 1 and Line 2 as the desired line whereVFD will be temporarily shown if ‘Temp’ is selected at ‘Display’ option asdescribed above.ON-SCREEN DISPLAY (OSD)Temp Disp: This applies to the OSD that is temporarily shown at video outwhenever any of the front panel controls or their corresponding keys in theremote control is activated. Set to ‘On’ if it is desired to show the applicableOSD at the monitor/TV; otherwise, select ‘Off’.OPERATIONUSING THE T 785 – SETUP MENU0ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ