NAPCO Gemini GEM-P1632 Installation Instructions Manual

Also see for Gemini GEM-P1632: Installation instructions Programming instructions Installation instructions Installation instructions Installation instructions

NAPCO Gemini GEM-P1632 Installation Instructions Manual Manual pdf 21 page image

L NAPCO Security Systems X GEM-P1632 Installation InstructionsWI808F 8/03 !Page 21BASIC OPERATIONThis section provides a brief overview of system operation. For detailed operation, refer to the User's Guide furnishedwith the keypad (see page 7 for a listing of User Guides for each keypad) and to the Keypad Programming Modes at theend of this manual. NOTE: Keypad displays shown in this text are for the GEM-RP1CAe2/GEM-K1CA keypads. GEM-RP2ASe2/GEM-K2AS displays will be similar, although abbreviated, and will scroll automatically.USER CODES & ZONE DESCRIPTIONS(Refer to the GEM-P1632 Programming Instructions (WI897 and WI1148) for a detailed explanation of programming).Up to 32 personal user codes may be programmed at the keypad. NOTE: The Area Options associated with each UserCode may only be programmed in the Dealer Program Mode.Default User Code.The first code programmed should replace the default (User 01) code, ìU01 123 ï ï ï - ï ï - ï ï î, (1,2,3), which should notbe selected as a user code.Each user should be assigned his own dissimilar code and should be cautioned against divulging his code to anyoneelse. Thus should it become necessary to remove a user from the system, that one code may be cancelled withoutaffecting other codes, and that user would then be prevented from entry. Note: Duplicate User Codes are not allowed bythe panel; therefore a duplicate Code entered in the LCD Window will erase when U is pressed.Changing or Canceling a User CodeTo change any user code, merely program over the existing user code as described in the Programming Instructions.Similarly, to cancel a user code, blank out each number of the user code.Arm/Disarm Code (Programmable in Dealer Program Mode only)An Arm/Disarm Code may be used to arm/disarm the area in which it is programmed. Up to 6 digits may beprogrammed or it may be programmed as a two-digit code for the purposes of arming quickly.Arm-Only Code (Programmable in Dealer Program Mode only)An Arm-Only Code may only be used to arm the area in which it is programmed; it never has any disarm capability. Upto 6 digits may be programmed or it may be programmed as a two-digit code for the purposes of arming quickly.Service Code (Programmable in Dealer Program Mode only)A Service Code is an Arm/Disarm Code that is easily activated when needed, and dormant at other times. Intended forthe occasional or temporary user (repairman, etc.) who would otherwise be denied access to the premises. It may thenbe used to arm and disarm just as any other User Code. A Service Code can be armed/disarmed from a disarmedstate, but it cannot be armed/disarmed from an armed state, after another user code has been entered. Up to 6 digitsmay be programmed or it may be programmed as a two-digit code for the purposes of quicker arming.Access CodeThe Access Code will trip the panel's PGM2 Output Relay while armed or disarmed if the ìAccess Control on PGM2Outputî and ìPGM2 Output Access Control Timeî is programmed. The Access Code is programmed as any other usercode but without arm/disarm capability. Note: These systems have not been investigated by UL for compliance withUL294 (Access Control Systems).Ambush CodeThe Ambush Code is special user code entered by the user typically to cause a silent report to be sent to the centralstation. Thus, should the user be forced to disarm by an assailant, he can silently signal an emergency while appearingto be merely disarming the panel. (Check the glossary for programming required to enable this feature).Zone Descriptions. (GEM-RP1CAe2/GEM-K1CA only)Zone descriptions follow the Program Code in the normal programming sequence (ì01-î will appear in the display).Program the description, up to two lines, letter by letter. Buttons 1 and 2 control the position of the cursor.Basic Operation: User Codes