L NAPCO Security Systems X GEM-P1632 Installation InstructionsWI808F 8/03 !Page 23Basic Operation: Arming in Stay Mode to Instant ArmingInstant ArmingINSTANT ARMING allows exit/entry zones to immediately go into alarm when violated, with no Exit/Entry time delay. Thisfeature can be used to provide instant protection while you or someone else is on the premises. With the "Classic" keypads,to arm "Stay" and obtain Instant Arming, press E and F, then enter your user code and press D. With the "K Se-ries" keypads, enter your user code and press P. Then press and hold P until keypad beeps Instant Arming will beautomatically reset on disarming.Auto Arming (Not for UL Installations)AUTO ARM allows the User to automatically arm the system at a specified time of the day and on specific days of the week.Schedule a specific closing time on any/all day(s) of the week. After a specific Fail-to-Close Window Start Time, if the userhas not Armed the system during the Window Length, and the system has been instructed to ìFail-to-Closeí and ëAuto Arm ifnot closed at end of Windowî then the system will arm, providing a 15 minute warning. CAUTION: If Automatic Interior By-pass is selected, panel will Auto Arm in STAY Mode.Delaying an Auto Arm (Not for UL Installations)During the 15 minute pulsating sounder warning of an Auto Arm, a User can press the R or A button, until ìTODELAY AUTO ARM / PRESS 1-4 / Nî is displayed. Enter the number of hours to delay arming, followed by the U or D but-ton. If ìDELAY AUTO ARM Y/Nî is displayed, press the ìNEXT/YESî button. The sounder can be silenced by pressing the Cbutton during the 15 minute interval, but will come back on in the last 1 minute. This feature may be canceled by arming anddisarming the keypad.EZ Arm (Easy Arm)EASY ARM provides one button arming for non-security critical premises. Select Easy Arming for each Keypad, with optionalreporting of Easy Arm Closings as User 35. Disarming still requires a valid user code.!To arm, press the U button for "Classic" keypads;!To arm, press and hold P or Q for 3 seconds for "K Series" keypads.Keyswitch ArmingKEYSWITCH ARMING allows a zone input to be used to arm/disarm. The area will arm/disarm when the zone ismomentarily shorted through a Momentary Switch. An end-of-line resistor must be used. Select Keyswitch Arm tooptionally report as User 36.Maintained-Key Input ArmingKEYSWITCH ARMING with MAINTAINED-KEY INPUT ARMING is similar to Keyswitch arming, except the zone inputmust remain shorted to be armed and remain open to be disarmed.Remote Arming (Not for UL Installations)REMOTE ARMING allows computer software control of arming/disarming of the system for non-security criticalinstallations. Select Remote Arm to optionally report as User 34.Priority ArmingA 2-second tone and ìCANíT ARM SYSTEM/ZONE FAULTEDî displayed when attempting to arm indicates a priority condition; thatis, a problem exists on at least one zone that has been designated as a Priority Zone, or a system trouble exists. Thetrouble(s) must be corrected before the panel can be armed. The display will read ìZONE FAULTEDî, then automaticallyscroll through all unsecured zones. If a system trouble is indicated, it will display the system trouble.Area Arming/Managerís ModeIn a partitioned system, either or both secured areas may be armed (or disarmed) from the Manager's Mode (if enabled).The Manager's Mode, is a low-security mode of operation. It provides quick access to other areas without having to goto another keypad of another area.To arm or disarm the alternate area (for "Classic" keypads):