E-51Operation Using an HTTP BrowserOverviewThe use of HTTP server functions will allow control of the projector froma web browser without the installation of special software. Please besure to use “Microsoft Internet Explorer 4.x” or a higher version for theweb browser. (This device uses “JavaScript” and “Cookies” and thebrowser should be set to accept these functions. The setting methodwill vary depending on the version of browser. Please refer to the helpfiles and the other information provided in your software.)NOTE:* The use of HTTP server functions is not available during Standby mode.* The display’s or button’s response can be slowed down or operation may notbe accepted depending the settings of your network. Should this happen, con-sult your network administrator.* The projector may not respond if its buttons are repeatedly pressed in rapidintervals. Should this happen, wait a moment and repeat. If you still can’t getany response, pull out and then re-insert the LAN card.Access is gained to the HTTP server functions by specifyinghttp:// /index.htmlin the entry column of the URL.Preparation Before UseMake network connections and set up the projector and confirm that itis complete before engaging in browser operations. (See “Setting LANMode” on page E-34.)Operation with a browser that uses a proxy server may not be possibledepending on the type of proxy server and the setting method. Althoughthe type of proxy server will be a factor, it is possible that items that haveactually been set will not be displayed depending on the effectivenessof the cache, and the contents set from the browser may not be re-flected in operation. It is recommended that a proxy server not be usedunless it is unavoidable.Handling of the Address for Operation via a BrowserRegarding the actual address that is entered for the address or enteredto the URL column when operation of the projector is via a browser, thehost name can be used as it is when the host name corresponding tothe IP address of the projector has been registered to the domain nameserver by a network administrator, or the host name corresponding tothe IP address of the projector has been set in the “HOSTS” file of thecomputer being used.Example 1: When the host name of the projector has been set to“pj.nec.co.jp”, http://pj.nec.co.jp/index.html is specified for the ad-dress or the entry column of the URL.Example 2: When the IP address of the projector is “192.168.73.1”,access is gained to the HTTP server functions by specifyinghttp://192.168.73.1/index.html for the address or the entry columnof the URL.Structure of the HTTP ServerPower: This controls the power of the projector.On .................. Power is switched on.Off .................. Power is switched off.Volume: This controls the volume of the projector. .................... Increments the volume adjustment value. .................... Decrements the volume adjustment value.Mute: This controls the mute function of the projector.Picture On ...... Mutes the video.Picture Off ...... Cancels the video muting.Sound On ...... Mutes the audio.Sound Off ...... Cancels the audio muting.OSD On ......... Mutes the on-screen display.OSD Off ......... Cancels the muting of the on-screen display.All On ............. Mutes each of the video, audio, and on-screen dis-play functions.All Off ............. Cancels the muting of each of the video, audio, andon-screen display functions.Picture: Controls the video adjustment of the projector.Preset 1-5Brightness .. Increments the brightness adjustment value.Brightness .. Decrements the brightness adjustment value.Contrast ..... Increments the contrast adjustment value.Contrast ..... Decrements the contrast adjustment value.Color .......... Increments the color adjustment value.Color .......... Decrements the color adjustment value.Hue ............ Increments the hue adjustment value.Hue ............ Decrements the hue adjustment value.Sharpness . Increments the sharpness adjustment value.Sharpness . Decrements the sharpness adjustment value.* The functions that can be controlled will vary depending on the sig-nal being input to the projector.Source Select: This switches the input connector of the projector.Video ............. Switches to the Video connector.S-Video .......... Switches to the S-Video connector.Component .... Switches to the Component connectors.Computer ....... Switches to the Computer connector.DVI (DIGITAL) Switches to the DVI-D connector.Viewer ............ Switches to the Viewer.Projector Status: This displays the condition of the projector.Refresh ......................... Updates the display of the following condi-tions.Remaining Lamp Time .. Displays the remaining life of the lamp as apercentage.Projector Usage ............ Displays how many hours the projector hasbeen used.Lamp Hour Meter .......... Displays how many hours the lamp has beenused.Error Status .................. Displays the status of errors occurring withinthe projector.
