4 1To unpair a paired the Bluetooth ® device, select the device in the [Delete] screen.▼ Other Setting and CheckSet whether to make information about the IP3NA-BCH ADAPTER( ) visible to other Bluetooth ® devices(default: [1. Disable]).You can view the following kinds of information about the IP3NA-BCH ADAPTER( ):・ Firmware and hardware versions・ Bluetooth ® module information andstandard・ Installed profile versions・ Device address and name▼ Specifications※ Bluetooth ® is a registered trademark owned by Bluetooth SIG, Inc. and is licensed to NEC InfrontiaCorporation.▼ IntroductionThe IP3NA-BCH ADAPTER( ) is an adapter that connects a Bluetooth ® device to a multifunctional tele-phone.The table below lists the type of device that can be connected to the IP3NA-BCH ADAPTER( ) and thefunctions supported by it.Item SpecificationDestination Multifunctional telephone bottom-unit connector (except for economy multifunctional telephone)Bluetooth ® version Bluetooth ® version 2.0Radio interface Bluetooth ® Class1(1 to 100mW)Installed profiles ă GAP : Generic Access Profile ă HSP : Headset Profileă SPP : Serial Port Profile ă HFP : Hands Free ProfilePower consumption About 0.8 W (excluding the telephone)Power feeding method Power feeding from the multifunctional telephoneDimensions (L ×W × H) 72mm × 65mm × 25mmMass 0.1kgOperating environment Temperature: 0 to 40℃ , Relative humidity: 10 to 90% (no dew condensing)Restrictions Keep the IP3NA-BCH ADAPTER( ) at least 1m apart from other IP3NA-BCH adaptersand at least 3m apart from other radio equipment.=2CKTKPI?ĉĊ$CEM1-Ĵ Ĵĵ=$NWGVQQVJ*GCFUGV?&GNGVG%QPPGEVĉĊ$CEM1-=&GNGVG?&GNGVG$6&GXKEG1-!$CEM1-Ĵ Ĵ=$NWGVQQVJ?2CKTKPI/QFG8KUKDKNKV[ĉĊ$CEM1-Ĵĵ=8KUKDKNKV[?&KUCDNG'PCDNGĉĊ$CEM1-ĴĵĴĵ=$NWGVQQVJ?$6+PHQTOCVKQPĉĊ$CEM1-Ķ=$6+PHQTOCVKQP?(KTOYCTG8GTUKQP::ZZ*CTFYCTG8GTUKQP::ZZĉĊ'ZKVĶ Type of device Available function RemarksBluetooth ®headset・Originating calls to an extension or central office linePress the headset call (call control) key twice briefly and per-form a dialing operation from the telephone.・Answering terminating callsPress the headset call (call control) key while a call termi-nates with a ring tone.※ The headset call control key allows you to only originatecalls from the headset and answer terminating calls.Any other headset-specific functions are not supported.※ The handset cannot be used while you are talking with theBluetooth® headset on. You cannot switch to the Bluetooth®headset to use while you are using the handset, either.・The ringing of calls terminat-ing to the headset is linkedwith that of the telephone,though some ringing fea-tures, such as a busy tone,are not supported.※ For latest information aboutrecommended products,browse the following Website:http://www.necinfron-tia.co.jp/・A headset with built-in Bluetooth ® supporting the HFP/HSP profiles can be connected to the IP3NA-BCHADAPTER( ).・The receiver volume can be controlled with the multifunctional telephone (the cursor up and downkeys or the volume key).・Whether the functions mentioned above work or not depends on the destination system. For moredetails, refer to the use’s guide that comes with the destination system.・The ways you originate calls from the Bluetooth ® headset and answer terminating calls may varydepending on the type of device you use.A50-013691-001Issue 1.02008.4IP3NA-BHA ADAPTER Connection ManualBHA-L UNITBluetooth -readyheadsetRCaution
