NEC MultiSync PA242W User Manual

English-23EnglishPOWER SAVETIMERON: Monitor automatically changes to OFF mode after 2 hours of continuous no-videosignal.OFF: Monitor will not automatically change to OFF mode when no video signal isconnected.OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode aftera period of inactivity. The OFF MODE has four settings.OFF: Monitor does not go into power save mode when the input signal is lost.STANDARD: Monitor enters power save mode automatically when the input signal is lost.ADVANCED: The signal detection circuit works always. Recovery time to normal mode isfaster than STANDARD. Power consumption is higher than STANDARD.NOTE: When set to STANDARD, if the image does not reappear when the signal isrestarted, please change the setting to ADVANCED.OPTION: Monitor enters power save mode automatically when the amount ofsurrounding light goes below the level that is determined by the user.OFF MODE SETTING Adjusts the ILLUMINANCE value for OFF MODE. Shows illuminance.LED BRIGHTNESS* 2 Controls the brightness of the power LED on the monitor.LED COLOR* 2 Toggles the power LED on the front between blue or green.Tag7 LANGUAGE* 2 OSD control menus are available in nine languages. Press “LEFT” or “RIGHT” to select.OSD H.POSITION You can choose where you would like the OSD control image to appear on your screen.Selecting OSD Location allows you to manually adjust the position of the OSD controlmenu left or right.OSD V.POSITION You can choose where you would like the OSD control image to appear on your screen.Selecting OSD Location allows you to manually adjust the position of the OSD controlmenu up or down.OSD TURN OFF The OSD control menu will stay on as long as it is use. You can select how long themonitor waits after the last touch of a button to shut off the OSD control menu.The preset choices are 10-120 seconds in 5 second increments.OSD LOCK OUT*2 This control completely locks out access to all OSD control functions. When attemptingto activate OSD controls while in the Lock Out mode, a screen will appear indicating theOSD controls are locked out.There are three types of OSD LOCK OUT:OSD LOCK OUT with no control: To activate the OSD Lock Out function, press SELECT,then “RIGHT” button and hold down simultaneously. To deactivate the OSD Lock Out,press SELECT, then “RIGHT” button and hold down simultaneously while in the OSDmenu. No controls can be adjusted while in the lock out mode.OSD LOCK OUT with BRIGHTNESS (only) control: To activate the OSD LockOut function, press SELECT, then “DOWN” and “LEFT” buttons and hold downsimultaneously. To deactivate the OSD Lock Out, press SELECT, then “DOWN” and“LEFT” buttons and hold down simultaneously while in the OSD menu. BRIGHTNESScan be adjusted while in the lock out mode.CUSTOM: Press RESET and EXIT to enter the CUSTOM Menu. Select ENABLE orDISABLE for POWER KEY, INPUT SEL, HOT KEY (BRIGHTNESS), PICTURE MODE,WARNING (RESOLUTION NOTIFIER/OSD LOCK OUT). To Deactivate the OSD LockOut function, press RESET and EXIT to bring up the LOCK OUT warning.Press SELECT, SELECT, <, >, <, >, EXIT.OSD TRANSPARENCY Adjusts the transparency of the OSD MENU.OSD COLOR* 2 “Tag window frame color”, “Item select color” & ”Adjust Window frame color” can bechanged.BOOT LOGO* 2 The NEC logo is briefl y displayed after the monitor is powered on. This feature can beturned on or off in the OSD.Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGOmenu will appear. It is possible to change the BOOT LOGO setting to OFF.SIGNALINFORMATION*2Signal information can be displayed in the corner of the screen.Signal information is either “ON/OFF”.RESOLUTIONNOTIFIER*2The optimal resolution is 1920 x 1200 for PA242W, 2560 x 1440 for PA272W or2560 x 1600 for PA302W. If ON is selected, a message will appear on the screen after30 seconds, notifying you that the resolution is not set to 1920 x 1200 for PA242W,2560 x 1440 for PA272W or 2560 x 1600 for PA302W.Press “LEFT” or “RIGHT” to select.*2 This item does not reset by FACTORY PRESET (Tag7).