NEC MultiSync PA322UHD-2 User Manual

English-16PIP SIZESelects the size of the sub-picture used in PIP mode.MULTIPICTUREPICTUREPATTERN Picture 1 Picture 2 Picture 3 Picture 4OFF - - - - -PIP - - -PBP 2 - -PBP 4*2PBP(Portraitmode)4*2Picture1 Picture2DP1 OPTION (built-in) HDMI1 HDMI2 HDMI3 HDMI4 DVI-D1 DVI-D2DP1 Yes*Yes* 1 YesYes YesYes YesYes YesYes YesYes YesYesOPTION (built-in) Yes*Yes* 1 No*No*1 Yes*Yes* 1 Yes*Yes* 1 Yes*Yes* 1 No*No*1 Yes*Yes* 1HDMI1 YesYes No*No*1 YesYes YesYes YesYes NoNo NoNoHDMI2 YesYes Yes*Yes* 1 YesYes YesYes YesYes NoNo NoNoHDMI3 YesYes Yes*Yes* 1 YesYes YesYes YesYes NoNo NoNoHDMI4 YesYes Yes*Yes* 1 YesYes YesYes YesYes NoNo NoNoDVI-D1 YesYes No*No*1 NoNo NoNo NoNo NoNo YesYesDVI-D2 YesYes Yes*Yes* 1 NoNo NoNo NoNo NoNo YesYes* 1 This combination is not available in PIP (Picture In Picture) mode.*2 The built-in option board does not be displayed.NOTE: Depending on the option board which you use, some combinations may not be available. Please contact yoursupplier for available option boards.USB SELECTChange USB upstream input (1 or 2) associated with the current display input. When connecting a computer to eachof the upstream ports, the monitor's USB downstream ports can be used by selecting this setting for the current inputsignal.You can change the active display and upstream USB port combination by using the Input button (see page 13).You can set the USB selection for each input signals in Advanced menu (see page 23).When using only one upstream port, the connected upstream port is used by default.NOTE: To avoid data loss, before changing USB upstream ports, ensure that no USB storage devices are in use bythe operating system of the computer attached to the USB upstream port.VIDEO DETECTSelects the method of video detection when more than one video input is connected for active picture.FIRST: When current video input signal is not present, then the monitor searches for a video signal from the othervideo input port(s)*3. If a video signal is present in another port, then the monitor switches the video source input portto the new found video source automatically. The monitor will not look for other video signals while the current videosource is present.LAST: When the monitor is displaying a signal from the current source and a new secondary source is supplied tothe monitor, then the monitor will automatically switch to the new video source. When current video input signal is notpresent, then the monitor searches for a video signal from the other video input port(s)*3. If the video signal is presentin another port, then the monitor switches the video source input port to the new found video source automatically.NONE: The Monitor will not search the other video input port unless the monitor is turned on.NOTE: When HDMI1 or DVI1 is set, HDMI and DisplayPort Input Card signal (OPTION) detection is not available.When HDMI and DisplayPort Input Card input (OPTION) is set, HDMI1 or DVI1 detection is not available.When HDMI and DisplayPort Input Card input (OPTION) is set, LAST may not work.*3 When HDMI1, DVI1 or HDMI and DisplayPort (OPTION) is set, this function may not work.OFF TIMERMonitor will automatically power-down when you have selected a pre-determined amount of time.Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes.Press any OSD button to delay the power-down time.PICTURE is OFF inROTATION inAdvanced Menu TagAPICTURE is ON inROTATION inAdvanced Menu TagA