NEC VT45 Quick Connect Manual

Also see for VT45: User manual Specifications Installation data User manual User manual

Contents

remote control features

NEC VT45 Quick Connect Manual Manual pdf 1 page image

Quick Connect GuideRemote Control Features6 Volume ( + / – ) ButtonsPress and hold (+) to increase the volume.Press and hold (–) to decrease the volume.7 Picture ButtonPress to display the Picture adjustment menu. Each timethis button is pressed, the highlight will move as follows:Brightness → Contrast → Color → Hue → Sharpness → …You can also select the Picture adjustment item by usingthe select up or down button.If no adjustments are performed within 3 seconds, thePicture adjustment menu will disappear.8 Freeze ButtonPress to freeze a picture. Press again to resume motion.9 Mute ButtonThis button turns off the image and sound. Press again torestore the image and sound.10 Aspect ButtonPress to display the Aspect Ratio select menu.Each time this button is pressed, the current aspect ratiowill change as follows:Normal → Zoom → Wide Zoom → Cinema → Normal → ...You can also select the aspect ratio by using the Selectbutton.If no adjustments are performed within 3 seconds, theAspect Ratio select menu will disappear.11 Menu ButtonDisplays the menu.12 Help ButtonProvides information about the current signal and the statusof the projector.13 Select ( ) Buttons: Use these buttons to select the menu of the itemyou wish to adjust.: Use these buttons to change the level of a selectedmenu item.A press of the button executes the selection.14 Enter ButtonUse this button to enter your menu selection.15 Cancel ButtonPress this button to close menu.1 Infrared TransmitterDirect the remote control toward the remote sen-sor on the projector cabinet.2 Power ButtonUse this button to turn your projector on and off.NOTE: To turn off the projector, press and holdthe POWER button for a minimum of two seconds.3 Source ButtonsPress to select an input device.4 Auto Adjust ButtonUse this button to adjust Position-H/V and PixelClock/Phase for an optimal picture.5 Magnify ( + / – ) ButtonsUse the (+) or (–) button to adjust the image sizeup to 400%.ConnectionsSOURCEAUTO ADJUSTON STAND BYSTATUSPOWEREMNUCNACELTERNESELECTVIDEOINRGB OUTS-VIDEOINRGB INR INL/MONOININOUTAUDIOCONTROLPCRGB OUTRGB INStep 2 Connect the supplied power cable.AC INSOURCEAUTO ADJUSTON STAND BYSTATUSPOWEREMNUCNACELTERNESELECTINOUTININL/MONORININRGB OUTRGB INCONTROLPCStep 3 Turn on the projector.SOURCE AUTO ADJUSTON STAND BYSTATUSPOWEREMNUCNACELTERNESELECTStep 4 Set up the Projector.To adjust the projector’s lens shift, focus or to zoom in and out usethe Lens Shift, Focus ring or Zoom lever on the lens.To optimize image, press the AUTO ADJUST button on the cabinetor the remote control.AC INSOURCEAUTO ADJUSTON STAND BYSTATUSPOWEREMNUCNACELTERNESELECTINOUTININL/MONORININRGB OUTRGB INCONTROLPC211SOURCEAUTO ADJUSTON STAND BYSTATUSPOWEREMNUCNACELTERNESELECTAC ININOUTININL/MONORININRGB OUTRGB INCONTROLPC21For older Macintosh computers, use acommercially available pin adapter toconnect to your Macintosh’s video port.Power down all equipmentbefore making connections.Power button NOTE: To turn off the projector,press and hold the POWER buttonfor a minimum of two seconds.Using the Lens Shift1 Grip the lens shift lever on the top and bottom.2 Hold the lever to move the lens vertically or horizontally.See page E-14 for Lens Shift Adjustable Range.Adjusting the Tilt Foot1 Press and hold the Tilt button on the front of the projector.2 Lift the front edge of the projector to the desired height, and release the button to lock the Adjustable TiltFoot.• If the projected image does not appear square to the screen then use keystone correction for proper adjustment.Focus ringZoom leverNOTE: The POWER, AUTO ADJ., MENU, SELECT, ENTER and CANCEL buttons on the remote control perform the samefunctions as the corresponding buttons on the projector cabinet. The remaining buttons are on the remote control only.VOLUMERGB VIDEO S-VIDEO POWERAUTO ADJ.MAGNIFYPICTURE FREEZE MUTE ASPECTMENUENTERHELPCANCELRD-372E134578111469101512132Printed in China7N8P0891Step 1 Connect the supplied 15pin-15pin signal cable.Monitor

/ 2

Related manuals for NEC VT45