Napoleon B35NT Installation And Operation Manual

Contents

Napoleon B35NT Installation And Operation Manual Manual pdf 49 page image

ENW415-1399 / C / 08.16.184911.0 optional (AUB) blower installation• Ensure the appliance is completely cool before starting installation.• To avoid danger of suffocation, keep the packaging bag away from babies and children. Do not use in cribs,beds, carriages, or play pens. This bag is not a toy. Knot before throwing away.! WARNING1. Remove the safety barrier by lifting it up and off the appliance.2. Remove the door from the appliance by releasing the four latches.3. Attach the two 1/4" connectors (black and white) from the wire harness to the thermodisc.4. Attach the two 1/4" connectors (black and red) from the wire harness to the blower.5. Install the clear bumpers (supplied) onto the bottom of the blower to avoid the blower rubbing against thefloor of the applinace.6. Pivot the blower into the bottom of the appliance, ensuring the gasket remains in place between the blowerand outer shell while sliding the blower against the left side of the outer shell into the blower mounting tab.Secure in place using one screw (Fig. 1 and 2).7. Place the control module back into its original position. Ensure the transformer is plugged into the rear outletof the electrical box.8. The variable speed swithc (VSS) will need to be disassembled to secure to the VSS bracket for installation.Place the VSS through the mounting bracket using the lock washer to secure it in place. Take the variablespeed switch knob and install into position (Fig. 3).9. To install the variable speed swtich, the mounting bracket will first need to be installed. Remove the twoscrews securing the piezo ignitor switch bracket in place. Install the VSS mounting bracket ito position thenreinstall the two previously removed screws (Fig. 3).10. Plug the connector from the variable speed switch to the matching connection of the wire harness.11. For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will bethe mounting tab for the thermal disc bracket (Fig. 4).12. Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screwssupplied (Fig. 4). Ensure that the thermal disc is in contact with the firebox base and that the wire harness isproperly attached.13. Plug the power cord from the blower into the electrical box.note:It may be necessary to move the control module aside during blower installation (electronic only).note:With the zip tie supplied, ensure all wires remain clear of the blower.note:The blower is thermally activated, so when it is turned on, it will automatically start approximately 15 minutesafter lighting the appliance and will run for approximately 30 minutes after the appliance has been turned off.BLOWERMOUNTING TABLOCATIONSCREWLOCATIONTo view a video of This insTallaTion visiT oUR weBsiTe aT: www.napoleonfireplaces.com/support/NOTE: fOr mOrE dETailEd iNsTrucTiONs rEfEr TO yOur iNsTallaTiON maNual.aub - aSCent univerSal blower inStallation inStruCtionSWolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • (705)721-1212 • fax (705)720-9081 • www.napoleonfireplaces.com! WARNINGENsurE THE uNiT is cOmPlETEly cOOl BEfOrE sTarTiNG iNsTallaTiON.TO aVOid daNGEr Of suffOcaTiON KEEP THE PacKaGiNG BaG aWay frOm BaBiEs aNd cHildrEN.dO NOT usE iN criBs, BEd, carriaGEs Or Play PENs. THis BaG is NOT a TOy. KNOT BEfOrETHrOWiNG aWay.W415-1479 / A / 05.09.16H. Place the control module back into its original position. Ensure the transformer is plugged into the rear outlet ofthe electrical box, refer to Figure 2.i. The variable speed switch (VSS) will need to be disassembled to secure to the VSS bracket for installation. Placethe VSS through the mounting bracket using the lock washer to secure it in place. Take the variable speed switchknob and install into position. (Refer to Figure 6.)J. To install the variable speed switch, the mounting bracket will first need to be installed. Remove the two screwssecuring the piezo ignitor switch bracket in place. Install the VSS mounting bracket into position then reinstallthe two previously removed screws, refer to Figure 6.BLOWER BLOWERMOUNTINGTABREAR VIEWa. Remove the screen by lifting it up and off of the appliance.B. Remove the door from the appliance by releasing the four latches.c. It may be necessary to move the control module aside during blower installation. (Electronic Only)d. Attach the two 1/4” connectors (black and white) from the wire harness to the thermodisc.E. Attach the two 1/4” connectors (black and red) from the wire harness to the blower.f. Install the clear bumpers supplied onto the bottom of the blower to avoid the blower rubbing against the floor ofthe appliance.G. Pivot the blower into the bottom of the appliance. Ensure the gasket remains in place between the blower andouter shell while sliding the blower against the left side of outer shell into the blower mounting tab. Secure in placeusing one screw, see Figures 4 and 5.NOTE: WiTH THE ZiP TiE suPPliEd, ENsurE all WirEs rEmaiN clEar Of THE BlOWEr.K. Plug the connector from the variable speed switch to the matching connection on the wire harness.l. For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will bethe mounting tab for the thermal disc bracket, see Figure 7.m. Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screws supplied,refer to Figure 7. Ensure that the thermal disc is in contact with the firebox base and that the wire harness isproperly attached.N. Plug the power cord from the blower into the electrical box, refer to Figure 2.NOTE: The blower is thermally activated, so when it is turned on, it will automatically start approximately 15minutes after lighting the appliance and will run for approximately 30 minutes after the appliance has been turnedoff.FIGURE 6VSSBRACKETPIEZO IGNITORBRACKETfiGURe 7THERMAL DISCBRACKETTHERMAL DISCMOUNTING TABFIREBOX BASEBLOWER BLOWERMOUNTINGTABREAR VIEWfiGURe 5fiGURe 4Fig. 1 Fig. 2BLOWERMOUNTING TABLOCATIONSCREWLOCATIONTo view a video of This insTallaTion visiT oUR weBsiTe aT: www.napoleonfireplaces.com/support/NOTE: fOr mOrE dETailEd iNsTrucTiONs rEfEr TO yOur iNsTallaTiON maNual.aub - aSCent univerSal blower inStallation inStruCtionSWolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • (705)721-1212 • fax (705)720-9081 • www.napoleonfireplaces.com! WARNINGENsurE THE uNiT is cOmPlETEly cOOl BEfOrE sTarTiNG iNsTallaTiON.TO aVOid daNGEr Of suffOcaTiON KEEP THE PacKaGiNG BaG aWay frOm BaBiEs aNd cHildrEN.dO NOT usE iN criBs, BEd, carriaGEs Or Play PENs. THis BaG is NOT a TOy. KNOT BEfOrETHrOWiNG aWay.W415-1479 / A / 05.09.16H. Place the control module back into its original position. Ensure the transformer is plugged into the rear outlet ofthe electrical box, refer to Figure 2.i. The variable speed switch (VSS) will need to be disassembled to secure to the VSS bracket for installation. Placethe VSS through the mounting bracket using the lock washer to secure it in place. Take the variable speed switchknob and install into position. (Refer to Figure 6.)J. To install the variable speed switch, the mounting bracket will first need to be installed. Remove the two screwssecuring the piezo ignitor switch bracket in place. Install the VSS mounting bracket into position then reinstallthe two previously removed screws, refer to Figure 6.BLOWER BLOWERMOUNTINGTABREAR VIEWa. Remove the screen by lifting it up and off of the appliance.B. Remove the door from the appliance by releasing the four latches.c. It may be necessary to move the control module aside during blower installation. (Electronic Only)d. Attach the two 1/4” connectors (black and white) from the wire harness to the thermodisc.E. Attach the two 1/4” connectors (black and red) from the wire harness to the blower.f. Install the clear bumpers supplied onto the bottom of the blower to avoid the blower rubbing against the floor ofthe appliance.G. Pivot the blower into the bottom of the appliance. Ensure the gasket remains in place between the blower andouter shell while sliding the blower against the left side of outer shell into the blower mounting tab. Secure in placeusing one screw, see Figures 4 and 5.NOTE: WiTH THE ZiP TiE suPPliEd, ENsurE all WirEs rEmaiN clEar Of THE BlOWEr.K. Plug the connector from the variable speed switch to the matching connection on the wire harness.l. For installation of the thermal disc bracket, bend the tab on the bottom of the firebox 90 degrees. This will bethe mounting tab for the thermal disc bracket, see Figure 7.m. Bend the thermal disc bracket 90 degrees and secure it to the firebox mounting tab using the two screws supplied,refer to Figure 7. Ensure that the thermal disc is in contact with the firebox base and that the wire harness isproperly attached.N. Plug the power cord from the blower into the electrical box, refer to Figure 2.NOTE: The blower is thermally activated, so when it is turned on, it will automatically start approximately 15minutes after lighting the appliance and will run for approximately 30 minutes after the appliance has been turnedoff.FIGURE 6VSSBRACKETPIEZO IGNITORBRACKETfiGURe 7THERMAL DISCBRACKETTHERMAL DISCMOUNTING TABFIREBOX BASEBLOWER BLOWERMOUNTINGTABREAR VIEWfiGURe 5fiGURe 4Fig. 3 Fig. 4