Napoleon B35NTE Installation And Operating Instructions Manual

Also see for B35NT: Installation and operation manual Installation and operating instructions

Contents

Napoleon B35NTE Installation And Operating Instructions Manual Manual pdf 10 page image

10W415-1399 / B / 06.17.16EN3.1 VENTING LENGTHS AND COMPONENTSUse only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab ventingcomponents. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from ventpipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adheredto. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedureprovided with the venting components.A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installationprocedure found on the website for your venting supplier.For vent systems that provide seals on the inner exhaust flue, only the outer air intake joints must be sealed using a red hightemperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of allother approved vent systems except for the exhaust vent pipe connection to the appliance flue collar which must be sealedusing the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.For optimum flame appearance and appliance performance, keep the vent length and number of elbows to a minimum.The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it isunobstructed and undamaged.Rigid and flexible venting systems must not be combined. Different venting manufacturer components must not becombined.FOR 4” / 7” (USE REDUCER KIT 4758AK TO TRANSITION FROM 5” / 8” TO 4” /7” VENTING)When using Wolf Steel venting components, use only approved Wolf Steel rigid / flexible components with the followingtermination kits: wall terminal kit GD222, GD222R, or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminalkit GD111, flat roof terminal kit GD112 or periscope kit GD201 (for wall penetration below grade). With flexible venting, inconjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD220 or the 10 foot (3.1m) vent kit GD330.These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections istwo horizontally or three vertically (excluding the appliance and the air terminal connections) when using flexible venting.FOR 5” / 8”When using Wolf Steel venting components, use only approved Wolf Steel rigid / flexible components with the followingtermination kits: wall terminal kit GD422-1, GD422R-1, or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12 roofterminal kit GD411, flat roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With flexibleventing, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) ventkit GD430.These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontalrun is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of ventconnections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when usingflexible venting.Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended that allhorizontal runs have a minimum 1/4” (6.4mm) rise per foot/meter using flexible venting. For safe and proper operation ofthe appliance, follow the venting instructions exactly.A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single familydwellings and serves both dwellings. Local codes or regulations may require different clearances.Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm)air gap all around between the inner liner and outer liner is required for safe operation.PART 4”/7” 5”/8” SUPPLIER WEBSITEDuravent W175-0053 W175-0170 Wolf Steel www.duravent.comAmerivent 4DSC-N2 5DSC-N2 American Metal www.americanmetalproducts.comDirect Temp 4DT-AAN 5DT-AA Selkirk www.selkirkcorp.comSuperSeal 4DNA 5DDA Metal-Fab www.mtlfab.com