Napoleon CONTINENTAL W175-0159 Instructions Manual

Napoleon CONTINENTAL W175-0159 Instructions Manual Manual pdf 1 page image

FUEL CONVERSION FOR MODELSBGD36/BCDV36, BGD36CF/BCDV36CF,BGNV36/BCNV36These kits are for use at altitudes of 0 to 4500 feet.This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’sinstructions and all applicable codes and requirements of the authority having jurisdiction. If theinformation in these instructions is not followed exactly, a fire, explosion or production of carbon monoxidemay result causing property damage, personal injury or loss of life. The qualified service agency isresponsible for the proper installation of this kit. The installation is not proper and complete until theoperation of the converted appliance is checked as specified in the owner instructions supplied with the kit.5 . Using a deep socket wrench, remove the main burner orifice. Aback-up wrench must be used on the manifold, located below thehousing to ensure that the aluminium tubing does not twist or kink.Replace the burner orifice supplied using pipe thread compound.6. Remove the burner hood from thepilot assembly by pulling vertically.Use an allen key to unscrew the injector.Replace the pilot injector with the onesupplied. Replace the pilot hood ontothe assembly ensuring key position forproper alignment. The fl ame openingon the hood must align with thethermocouple and the thermopile.7. Before replacing the burnerassembly, adjust the burner shutteropening.8. Replace and re-secure the burner assemblyand log support, ensuring that the venturi fitsover the burner orifice.9. Remove the venturi access cover andinspect to confirm correct venturi-orificeposition.10. To convert the main valve to the desiredfuel, follow the instructions that are suppliedwith the SIT regulator assembly kit.11. The conversion data label must be filled out and attachedadjacent to the valve.12. Turn on the gas supply and check for gas leaks by brushing on asoap and water solution.Do not use open flame.13. Replace the log set. Then light the pilot and main burner to ensurethat the gas lines have been purged.14. Close the glass viewing door. Turn on the electrical supply to theappliance.Purge all gas lines with the glass door open.Assure that a continuous fl ow is at the burner before closingthe door.Continued on reverse:ROI6WHHO/WG1DSROHRQ5G%DUULH21/0<&DQDGD ID[ ZZZQDSROHRQILUHSODFHVFRPPILOTHOODPILOTINJECTORSITW415-0971 / 11.17.10W175-0164, Propane to Natural Gas (BGD/BCDV36/36CF)W175-0280, Propane to Natural Gas (BGNV/BCNV36)REGULATOR ASSEMBLY 1#47 BURNER ORIFICE (IN KIT W175-0164) 1#48 BURNER ORIFICE (IN KIT W175-0280) 1CONVERSION DATA LABEL 1PILOT INJECTOR 1WARNING: Failure to position the parts in accordance with thesediagrams or failure to use only parts specifi cally approved withthis appliance may result in property damage or personal injury.CAUTION: The gas supply shall be shut off prior to disconnectingthe electrical power, before proceeding with the conversion.1. Open the glass viewing door and remove the log set.2. Remove the 3 screws securing the burner to the log support.3. Remove the log support by removing the 4 screws from the fireboxback.4. Remove the burner by removing the screw from each side of theburner.LOG SUPPORT SCREWSBURNER SCREWSBURNER BRACKET SCREWSBURNER ORIFICEPILOT ASSEMBLYW175-0159, Natural Gas to Propane(BGD/BCDV36/36CF,BGNV/BCNV36)REGULATOR ASSEMBLY 1#56 BURNER ORIFICE 1CONVERSION DATA LABEL 1PILOT INJECTOR 1INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOME OWNER.CHECK THE BOXES TO INDICATE THAT THE CORRESPONDING STEPS HAVE BEEN COMPLETED.

/ 4

Related manuals for Napoleon CONTINENTAL W175-0159