Necta KIKKO ES6 Installation, Use And Maintenance Manual

Necta KIKKO ES6 Installation, Use And Maintenance Manual Manual pdf 30 page image

© by NECTA VENDING SOLUTIONS SpA 26 02-2004 184 02MISCELLANEOUSThis menu contains some sub-menus, used less fre-quently, which permit control of the functions describedbelow.MACHINE INFORMATIONINSTALLATION DATEThis function is used to store the current date of system asinstallation date.The date is printed when retrieving the statistics.PROGRAMMING THE MACHINE CODEWhen the “Machine code” function is displayed the eight-digit numeric code identifying the machine can be changed(from the default 0).PROGRAMMING THE OPERATOR CODEWhen the “Operator code” function is displayed the six-digit numeric code identifying groups of machines can bechanged (from the default 0).INITIALISINGWhen the “Initialise” function is displayed the vendingmachine can be initialised restoring all default data.This function should be used if there is a memory data erroror when the software is replaced.All statistic information will be reset.Press confirm button “ ” and the display will indicate themessage “Confirm?”. Press the confirm button “ ” againand some parameters will be requested, which are:“Model”Defining whether the machine is Espresso or Instant“Country”intended as type of base doses for the different selections(e.g. IT coffee = 45 cc - FR coffee = 80 cc).According to the models, the available “countries” are Italy,France, Spain, Poland, England and Germany.“Layout”A number of Button/Selection combinations to choosefrom is provided for each model and dose type (thecombinations available for each layout are indicated in thedose selection table supplied with the machine).“Tank”Intended as water supply from a tank. This can be enabledor disabled (water supply from the mains).When confirming the options the message “Working” isdisplayed for a few seconds.EVADTS CODESThe EVADTS (European Vending Association Data Trans-fer System) communication protocol has two codes foridentifying the machine and for recognising the data trans-fer terminal:PASS CODEIt is a four-digit alphanumeric code (0-9; A-F) that must bethe same as the one in the data transfer terminal to allowits identification.Press the confirm button “ ” and the code is displayed as“0000” regardless of the actual value; then press thechange button “ ” and the first digit will start blinking.Using the scrolling buttons, its value can be changed(during the change operation the value becomes visible).Press the confirm button “ ” and the next digit startsblinking.Press the confirm key “ ” after changing the fourth digit;the value is stored and the display indicates “0000” again.SECURITY CODEIt is a further alphanumeric code for reciprocal recognitionbetween machine and EVADTS terminal.Programming works as in the “Pass” code.ConnectionThis function places the machine in wait mode for connec-tion to retrieve data.EVADTS CONNECTIONWhen activating this function, the machine awaits theconnection with a device to acquire the EVADTS statistics.GSMThe control software can send, via GSM modem, a signalindicating a machine failure or an “ending product” “pre-alarm”, after dispensing a certain (programmable) numberor quantity of a given product.The machine fitted with the modem can have the functionof “master GSM”, i.e. collect and transmit data from otherbanked machines.PIN CODEThis function is used for programming the identificationcode of the SIM card (0000 by default) that will be sent tothe GSM modem (optional) when switching the machineon.SETTING THE THRESHOLDSThis function is used for defining the number of pieces orgrams of powder for a given product, after which a “run-ning-out” “pre-alarm” is signalled via modem.RESETTING THE COUNTERSWith this function the counters that control the pre-alarmsare reset.When pressing the confirm button “ ” the values are reset.BANK NUMBERThe number in the bank of machines (1 to 7) that identifiesthe machines that have the “slave GSM” function, there-fore sending data via the modem of the “master” machine.The number 0 identifies the machine that is connecteddirectly to the modem, i.e. the “master GSM”.