Net Media SCM1 Specifications
Also see for SCM1: Troubleshooting tips
    | |
NM-MODLAMPMAN-MODLAMP REV0708AFigure 5 - Bypassing a digital or analog cable box and recombining to a single coax input on the TV. The kit’s filterremoves any conflict on channel 3 or 4. Switch TV from the cable box to the camera channel.NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.comPower InjectorCameraMain cable orAntennaSplitter/CombinerOptional NM-CNF7080 Ch. 70-80 Notch Filterwhen there are no clear cable channels.The notch filter does not bypass the cable box.TelevisionCable BoxNetMedia Cable BoxBypass/CombinerKit NM-ACB3The kit filter does notmake clear channelsfor the camera.Q- Why do the light areas of the picture look washed out?A- The camera’s automatic iris must decide how much to open for shadow areas or close for light areas. When a picture has bothlight and shadow, the camera adjusts the iris based on the percentage of each area in the image. If it decides to open more forthe shadow portions then the light areas will be overexposed. In addition, cameras that are designed for low light or infraredsensitivity typically favor the shadow areas and look more washed out under bright conditions. Try adjusting the image fieldso that more light areas are visible and see if the iris closes to improve the picture. It is normal though, that as the lightingconditions change throughout the day, so will the camera iris and the picture’s dark or light areas.Q- Why are the shadow areas too dark to see much detail?A- This is like the washed out question above except opposite. In this case, the camera’s automatic iris is opening more for thelight areas at the expense of the shadow areas. Try adjusting the image field so that more shadow areas are visible and see ifthe iris opens to improve the picture. Keep in mind though, that the camera still does need some kind of light in order to see.If necessary, add some lighting to the dark area to improve visibility.Q- How do I find out if the camera is working when I can’t see it on any televisions?A- Start with a basic setup: connect camera to coax, coax to power injector, power injector to TV with no amplifiers, splitters, filters,cable boxes or other devices involved. Set the camera to a channel that matches the TV mode: 14-69 for Antenna tuning; 70-94or 100-125 for Cable tuning. If the TV can tune channel 70 or above, then it is probably in Cable tuning mode. Set a simplechannel like 20 or 120 and look for it on the TV. Check power, power injector direction, connections, cables, TV tuning mode,and camera switches to correct any problems. You must see the camera picture to confirm that it works in this basic setupbefore moving on to more complex setups.Q- Why does the camera or cable service picture go bad when the two are combined together?A- The signals should be combined at the beginning of the distribution system before the cable service goes through anysplitters. Make sure you are not using any diplexers to split or combine. Once done, there is either interference or the signalsare not balanced. Most interference comes from invisible digital data that is on the line even when not subscribed to it. Set thecamera for a clear channel, try 120, or use a filter to remove the digital/analog interference. When there is no interference youcan balance the signals by amplifying the weaker, snowy one before the two are combined. 10 to 20dBmV is usually enough,too much will degrade the other signal.Q- Can the camera be combined with digital cable service?A- Yes. The difficulty is in finding a clear channel for the camera. The digital data usually takes up the analog channel range of80-117 so channel 120 is a good place to start. Analog 120 on the TV will not conflict with digital 120 on the cable box. If youcannot find a clear channel then you will have to use a notch or low pass filter on the cable service before you combine it withthe camera. Make sure the filter does not remove any subscribed digital services including an Internet connection. If only onelocation is using the digital services and it does not need to see the camera, you can split its run off before the main line isfiltered and combined with the camera. This prevents the filter from disrupting the digital data while enabling the camera toappear on the rest of the TV’s.Q- How can I see the camera when the TV uses a cable box?A- There are a few ways but they all involve bypassing the cable box and using the TV tuner to see the camera. Combine the camerawith the cable service and check its picture by connecting the coax directly to the TV. Any splitters, filters, or amplifiers you use forcombining are separate from the ones used to bypass the cable box. After verifying the camera picture, split the coax two wayswith one side going to the cable box. If you use the cable box S-Video or composite output then the other side of the splitter goesdirectly to the TV. If you use the cable box coax output and there is only one coax input on the TV, then you must use a ch. 3/4filter (included with NM-ACB3) and recombine the coaxes as shown in Figure 5. In any case, view the cable box through theappropriate TV connection, Video 1, ANT 2, channel 3/4, then change the TV (not the cable box) to the camera channel.Frequently Asked Questions |
Related manuals for Net Media SCM1
manualsdatabase
Your AI-powered manual search engine