Nidac 2 Series Instructions Manual
Also see for 2 Series: ManualInstructions
       | |
21SECURITY & PROTECTIONThe following common sense hints will help to maximise thesecurity of your system.• don’t use obvious codes such as 1234, or 888• change codes on a regular basis• ensure that knowledge of management and toggle codesis appropriately restrictedThe Presco™ system has a high immunity to all types ofstatic, EMF, and RF transmissions including those of policeand CB radio systems. Reverse polarity and over voltageprotection from lightning strike up to 10kV is provided.OTHER MODELS AND ACCESSORIESPRE Presco™ keypad encoder for Presco™ decoder.PSE Presco™ Stainless Steel vandal and weatherresistant keypad encoder for Presco™ decoder.PIM Presco™ Interface Module for Dallas iButton™,Clock & Data (Magnetic Card) or Wiegand readers.PAC1 Single Door Access Controller.PRX Presco™ proximity card reader for PAC1, PAC2 orWiegand input controller.CT1 User configurable general purpose timer module.22PROGRAMMING SUMMARYNote: The d shown in the programming sequences must bereplaced by a 1 for door 1 or 2 for door 2.Enable/Disable Automatic Relock. (default = enabled)*, 8, 0, d, x, E. x = 0 for disabled, x = 1 for enabled.Select EGRESS switch type. (default = N.O.)*, 8, 1, d, x, E. x = 0 for N.O., x = 1 for N.C.Select ELC relay type. (default = N.O.)*, 8, 2, d, x, E. x = 0 for N.O. (fail secure), x = 1 forN.C. (fail safe).Set ELC operating time. (default = 10 seconds)*, 8, 3, d, xxx, E. xxx = 1 to 255 (seconds).Enable/Disable DOOR input. (default = disabled)*, 8, 4, d, x, E. x = 0 for disabled, x = 1 for enabled.Set DOTL timer. (default = 60 seconds)*, 8, 5, d, xxxx, E. xxxx = 0 to 9999 (seconds).Enable/Disable Door Forced detection. (default = enabled)*, 8, 6, d, x, E. x = 0 for disabled, x = 1 for enabled.Enable/Disable 1 minute lockout. (default = disabled)*, 8, 7, d, x, E. x = 0 for disabled, x = 1 for enabled.Select Use Two Codes mode. (default = One User Code)*, 8, 8, d, x, E. x = 0 for One User Code Only, x = 1for Any Two User Codes, x = 2 for Code 000 or 001 andany other code, x = 3 for Sequentially Numbered UserCodes.Set Two Codes timing. (default = 60 seconds)*, 8, 9, d, xxx, E. xxx = 1 to 255 (seconds).23Program or change the Management Code.*, 9, E “code”, E.New Management CodeDelete the Management Code.#, 9, E.Program a User Code.*, nnn, m1, m2, E “code”, E.New User CodeDoor 2 Mode0 = Disabled1 = Momentary2 = ToggleDoor 1 Mode0 = Disabled1 = Momentary2 = ToggleMemory No. 000 to 399Change an existing User Code’s operating mode.*, nnn, m1, m2, E.Door 2 Mode0 = Disabled1 = Momentary2 = ToggleDoor 1 Mode0 = Disabled1 = Momentary2 = ToggleMemory No. 000 to 399Delete a User Code.#, nnn, E.Memory No. 000 to 399Exit Program Mode.#, 9, 9, E.Revision 3.0100%Designed and Manufactured by:NIDAC SECURITY PTY. LTD.2 CROMWELL STREETBURWOOD, VICTORIA Tel: (03) 9808 6244AUSTRALIA 3125 Fax: (03) 9808 9335 |
Related manuals for Nidac 2 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine