NightStick XPP-5418GX-01 Instruction Manual

NightStick XPP-5418GX-01 Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5418GX/RX-17 10-02-2017Instruction ManualXPP-5418GX/RX-K01Please read these instructions before using your Nightstick XPP-5418 IntrinsicallySafe Flashlight. They include important safety information and operating instructions.THE XPP-5418GX/RX IS APPROVED FOR USECLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135ºCCLASS I ZONE 0 AEx ia IIC T3 GaEx ia IIC T3 GaEx ia op is IIC T3 GaIntertek ITS 13 ATEX27837XIECEx ITS 16.0067X-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell with three in seriesEnergizer E91 or EN910359E 467756INTRINSICALLY SAFESECURITE INTRINSEQUEII 1 G Ex ia op is IIC T3 GaBayco Products, Inc. XPP-5418GX/RXWARNINGS:Replace batteries in a non-hazardous location.Use only Energizer AA Model E91 or EN91 batteries.AVERTISSEMENT:Remplacer les piles dans une zone non dangereuse.Utiliser uniquement les piles Energizer AA - modèle E91 ou EN91.Ex ia FLASHLIGHT FOR USE IN HAZARDOUS LOCATIONS640 S. Sanden Blvd., Wylie, TX 75098WARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable AA batteries with this light.y Warning: To prevent ignition of a hazardous atmosphere, do not open the lens bezelin the hazardous environment. This task must ONLY be performed in an area knownto be non-hazardous.y Warning: When exchanging batteries, use only Energizer EN91 or Energizer E91batteries.y Warning: To prevent ignition of a hazardous atmosphere, the AA batteries must onlybe exchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new batteries with usedbatteries, or mix batteries from different manufacturers.y Warning: Substitution of components may impair intrinsic safety.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYFor personal safety, always confirm the rating of any known hazardous or potentiallyhazardous location where the light is to be used.BATTERY INSTALLATIONWARNING: In order to maintain the XPP-5418’s Intrinsically Safe rating, the onlyAA batteries certified for use with this light are the Energizer EN91 or EnergizerE91 batteries.y Do not attempt to use any other brand or model of AA batteries.y Do not attempt to use any type of rechargeable AA batteries.Warning: To prevent ignition of a hazardous atmosphere, do not remove the lensbezel or the reflector / battery carrier in the hazardous environment. This task mustONLY be done in an area known to be non-hazardous.y Loosen the locking screw located on the side of the lens cap. NOTE: Do NOTattempt to completely remove the locking screw. Doing so is not necessary and maydamage the threads. The screw simply needs to be loosened enough to allow the lensbezel to unscrew.y Unscrew the lens bezel from the housing in a counter-clockwise direction.y Turn the light upside down and carefully shake the light in order to remove thebatteries. Allow the batteries to slide into your hand.y Using 3 – AA Energizer EN91 or Energizer E91 batteries (make sure that all 3batteries are of the same model), install the batteries in the carrier paying closeattention to the markings inside the housing for proper battery terminal polarityalignment.y Replace the lens bezel by screwing it onto the housing in a clockwise direction.y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage thethreads and impact the light’s Intrinsic Safety.ATTACHING HELMET MOUNTTHE XPP-5418-K01 COMES WITH THE NS-HMC6 MULTI-ANGLE MOUNT THAT CANBE ATTACHED TO ANY FIRE HELMET OR HARD HAT.Two mounting components are included that can be changed depending on whattype of mount is needed.y Brim Mount - Mounts on brim of helmet or hard hat..y Slot Mount - Slides into helmet accessory slot.NS-HMC6 Helmet Mount KitASSEMBLYy Fit the Light Mount (A) into the slot of either the Brim Mount or Slot Mount (B) andsecurely tighten using the thumb screw (C).y Securely attach the brim or slot mount to the helmet.y Place the flashlight inside the Light MountSET THE ANGLE OF THE MULTI-ANGLE MOUNTOnce mounted to the helmet, the user can change the angle of the mount in order toposition the light appropriately for the optimum clearance and illumination.OPERATIONTHE XPP-5418 HAS TWO SEPARATE LIGHTING MODES:MOMENTARY FLASHLIGHT MODELightly press the body switch for momentary operation. Release the switch to turnthe light off.CONSTANT-ON FLASHLIGHT MODEPress the body switch until it clicks and then release for constant-on mode. Pressand release the body switch again to turn the light off.WARRANTYLIMITED LIFETIME WARRANTYBayco Products, Inc. warrants this product to be free from defects in workmanshipand materials for the original purchaser’s lifetime. The Limited Lifetime Warrantyincludes the LEDs, housing and lenses. Rechargeable batteries, chargers, switches,electronics and included accessories are warranted for a period of two years with proofof purchase. Normal wear and failures which are caused by accidents, misuse, abuse,faulty installation and lightning damage are excluded.We will repair or replace this product should we determine it to be defective. Thisis the only warranty, expressed or implied, including any warranty of merchantability orfitness for a particular purpose.For a complete copy of the warranty, go to www.nightstick.com/nightstick-product-support/warranties. Retain your receipt for proof of purchase.XPP-5418 with Brim Mount XPP-5418 with Slot Mount

/ 4

Related manuals for NightStick XPP-5418GX-01