NightStick XPP-5422B Instruction Manual

Also see for XPP-5422B: Instruction manual Instruction manual Operating instructions Manual

NightStick XPP-5422B Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5422B/G/BA/GA-DL-21 09-24-2021Instruction ManualXPP-5422B / XPP-5422GXPP-5422BA / XPP-5422GATHE XPP-5422 IS APPROVED FOR USEPermissible Nightstick 5422 FlashlightAPPROVAL No. 20-A130001-0TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLYWARNINGS:CLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 IIC T3CLASS II ZONE 20 IIIC T135C-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell AA AlkalineID 4003544INTRINSICALLY SAFESECURITE INTRINSEQUEMSHA approved for use with three AA Duracell Type PC1500, EnergizerType EN91, and Energizer Type L91 batteries only.1)Replace the batteries in fresh air only and replace all batteries at thesame time. Do not mix batteries from different manufacturers or ofdifferent types.2)Energizer Lithium (Type L91) batteries are to be replaced by a qualifiedtechnician only.3)The Model Nightstick 5422 must not be opened in areas wherepermissibility is required.4)Bayco Products, Inc. XPP-5422BWylie, TX 75098640 S. Sanden Blvd.Permissible Nightstick 5422 FlashlightAPPROVAL No. 20-A130001-0TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLYWARNINGS:CLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 IIC T3CLASS II ZONE 20 IIIC T135C-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell AA AlkalineID 4003544INTRINSICALLY SAFESECURITE INTRINSEQUEMSHA approved for use with three AA Duracell Type PC1500, EnergizerType EN91, and Energizer Type L91 batteries only.1)Replace the batteries in fresh air only and replace all batteries at thesame time. Do not mix batteries from different manufacturers or ofdifferent types.2)Energizer Lithium (Type L91) batteries are to be replaced by a qualifiedtechnician only.3)The Model Nightstick 5422 must not be opened in areas wherepermissibility is required.4)Bayco Products, Inc. XPP-5422GWylie, TX 75098640 S. Sanden Blvd.CLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 AEx ia IIC T3 GaCLASS I ZONE 0 Ex ia IIC T3 GaEx ia op is I MaEx ia op is IIC T3 GaIntertek ITS 13 ATEX27837XIECEx ITS 16.0067X-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell AA Alkaline2575ID 4003544INTRINSICALLY SAFESECURITE INTRINSEQUEI M 1 Ex ia op is I MaII 1 G Ex ia op is IIC T3 GaBayco Products, Inc. XPP-5422BAWylie, TX 75098640 S. Sanden Blvd.Conforms to:ANSI/UL STD 913, ANSI/UL 60079-0,ANSI/UL 60079-11 ANSI/ISA 60079-26Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25Ex ia op is I MaEx ia op is IIC T3 Ga(-20ºC ≤ Tamb ≤ +40ºC)NCC 15.0286 XCLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 AEx ia IIC T3 GaCLASS I ZONE 0 Ex ia IIC T3 GaEx ia op is I MaEx ia op is IIC T3 GaIntertek ITS 13 ATEX27837XIECEx ITS 16.0067X-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell AA Alkaline2575ID 4003544INTRINSICALLY SAFESECURITE INTRINSEQUEI M 1 Ex ia op is I MaII 1 G Ex ia op is IIC T3 GaBayco Products, Inc. XPP-5422GAWylie, TX 75098640 S. Sanden Blvd.Conforms to:ANSI/UL STD 913, ANSI/UL 60079-0,ANSI/UL 60079-11 ANSI/ISA 60079-26Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25Ex ia op is I MaEx ia op is IIC T3 Ga(-20ºC ≤ Tamb ≤ +40ºC)NCC 15.0286 XWARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable AA batteries with this light.y Warning: To prevent ignition of a hazardous atmosphere, do not open the lens bezel inthe hazardous environment. This task must ONLY be performed in an area known to benon-hazardous.y Warning: When exchanging batteries, use only Duracell PC1500, Energizer EN91 orEnergizer L91 batteries.y Warning: To prevent ignition of a hazardous atmosphere, the AA batteries must only beexchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new non-rechargeable batteries with usednon-rechargeable batteries, or mix non-rechargeable batteries from different manufacturers.y Warning: Substitution of components may impair intrinsic safety.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYFor personal safety, always confirm the rating of any known hazardous or potentiallyhazardous location where the light is to be used.BATTERY INSTALLATIONWARNING: In order to maintain the Intrinsically Safe rating, the only AA batteriescertified for use with this light are the Duracell PC1500, Energizer EN91 or EnergizerL91 batteries.y Do not attempt to use any other brand or model of AA batteries with this light.y Do not attempt to use any type of rechargeable AA batteries with this light.Warning: To prevent ignition of a hazardous atmosphere, do not remove the lensbezel or the reflector / battery carrier in the hazardous environment. This task mustONLY be done in an area known to be non-hazardous.y Loosen the locking screw located on the side of the lens cap. NOTE: Do NOT attemptto completely remove the locking screw. Doing so is not necessary and may damage thethreads. The screw simply needs to be loosened enough to allow the lens bezel to unscrew.y Unscrew the lens bezel from the housing in a counter-clockwise direction.y Turn the light upside down and carefully shake the light in order to remove the reflector /battery carrier. Allow the reflector / battery carrier to slide into your hand. WARNING: Do NOTtouch the reflector surface with your finger. Doing so may damage the reflector surface.y Using 3 – AA Duracell PC1500, Energizer EN91 or Energizer L91 batteries (make surethat all 3 batteries are of the same model), install the batteries in the carrier paying closeattention to the markings on the battery carrier for proper battery terminal polarity alignment.y Align the reflector / battery carrier so that the switches on the carrier are aligned withthe switches on the housing. Carefully insert the reflector / battery carrier back into theflashlight housing until it is fully seated in the housing. WARNING: Be careful to not touchthe reflector surface with your finger. Doing so may damage the reflector surface.y Replace the lens bezel by screwing it onto the housing in a clockwise direction.y Tighten locking screw. CAUTION: Do not over-tighten. Doing so may damage thethreads and impact the light’s Intrinsic Safety.