NightStick XPP-5422GM Instruction Manual

Also see for XPP-5422GM: Instruction manual Instruction manual

NightStick XPP-5422GM Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mynightstick.comINS-XPP5422GM-15DPermissible Nightstick 5422 Flashlight/FloodlightAPPROVAL No. 20-A130001-0TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLYWARNINGS: MSHA approved for use with three AA Duracell Type PC1500, EnergizerType EN91, and Energizer Type L91 batteries only. Replace the batteries in fresh air onlyand replace all batteries at the same time. Do not mix batteries from differentmanufacturers or of different types. Energizer Lithium (Type L91) batteries are to bereplaced by a qualified technician only. The Model Nightstick 5422 must not be opened inareas where permissibility is required.CLASS I DIV 1 GRPS A-D T3CLASS II & III DIV 1 GRPS E-G T135CCLASS I ZONE 0 AEx ia IIC T3 GaCLASS I ZONE 0 Ex ia IIC T3 GaEx ia I MaEx ia IIC T3 GaIntertek ITS 13 ATEX27837XIECEx ETL 13.0026X&7DPE&1.5V/Cell AA Alkaline0359ID 4003544INTRINSICALLY SAFESECURITE INTRINSEQUEI M 1 Ex ia I MaII 1 G Ex ia IIC T3 GaConforms to:ANSI/UL STD 913, ANSI/UL60079-0, ANSI/UL 60079-11ANSI/ISA 60079-26Certified to:CAN/CSA STD C22.2 No 157CAN/CSA STD C22.2 No 60079-0CAN/CSA STD C22.2 No 60079-11CSA STD C22.2 No 25Instruction ManualXPP-5422GMTHANK YOU FOR SELECTING THE NIGHTSTICK XPP-5422GMINTRINSICALLY SAFE PERIMISSIBLE DUAL-LIGHT FLASHLIGHT W/DUAL MAGNETS!PLEASE SAVE THESE INSTRUCTIONSPlease read these instructions before using your Nightstick XPP-5422GMIntrinsically Safe Permissible Dual-Light Flashlight. They include importantsafety information and operating instructions.THE XPP-5422GM IS APPROVED FOR USECAPACITANCE LIMITATION - INTRINSICALLY SAFEThe capacitance measured on the two magnets and the side clip exceeds3pF for Group IIC. The user shall determine the suitability of the equipmentin the end application.WARNINGS - INTRINSICALLY SAFE Warning: Use only the approved non-rechargeable batteries listed below. Warning: Do NOT attempt to use rechargeable AA batteries with this light. Warning: To prevent ignition of a hazardous atmosphere, do not openthe lens bezel in the hazardous environment. This task must ONLY beperformed in an area known to be non-hazardous. Warning: When exchanging batteries, use only Duracell PC1500,Energizer EN91 or Energizer L91 batteries. Warning: To prevent ignition of a hazardous atmosphere, the AA batteriesmust only be exchanged in an area known to be non-hazardous. Warning: To reduce the risk of explosion, do not mix new non-rechargeablebatteries with used non-rechargeable batteries, or mix non-rechargeablebatteries from different manufacturers. Warning: Substitution of components may impair intrinsic safety.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY For personal safety, always confirm the rating of any known hazardous orpotentially hazardous location where the light is to be used.BATTERY INSTALLATIONWARNING: In order to maintain the XPP-5422GM’s Intrinsically SafePermissible rating, the only AA batteries certified for use with this lightare the Duracell PC1500, Energizer EN91 or Energizer L91 batteries. Do not attempt to use any other brand or model of AA batteries with thislight. Do not attempt to use any type of rechargeable AA batteries with this light.Warning: To prevent ignition of a hazardous atmosphere, do notremove the lens bezel or the reflector / battery carrier in the hazardousenvironment. This task must ONLY be done in an area known to benon-hazardous. Loosen the locking screw located on the side of the lens cap. NOTE:Do NOT attempt to completely remove the locking screw. Doing so is notnecessary and may damage the threads. The screw simply needs to beloosened enough to allow the lens bezel to unscrew. Unscrew the lens bezel from the housing in a counter-clockwise direction. Turn the light upside down and carefully shake the light in order to removethe reflector / battery carrier. Allow the reflector / battery carrier to slide intoyour hand. WARNING: Do NOT touch the reflector surface with your finger.Doing so may damage the reflector surface. Using 3 – AA Duracell PC1500, Energizer EN91 or Energizer L91 batteries(make sure that all 3 batteries are of the same model), install the batteries inthe carrier paying close attention to the markings on the battery carrier forproper battery terminal polarity alignment. Align the reflector / battery carrier so that the switches on the carrier arealigned with the switches on the housing. Carefully insert the reflector /battery carrier back into the flashlight housing until it is fully seated in thehousing. WARNING: Be careful to not touch the reflector surface with yourfinger. Doing so may damage the reflector surface. Replace the lens bezel by screwing it onto the housing in a clockwisedirection. Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so maydamage the threads and impact the light’s Intrinsic Safety.OPERATIONTHE XPP-5422GM HAS FOUR SEPARATE LIGHTING MODES: Momentary Flashlight Constant-on Flashlight Floodlight

/ 2

Related manuals for NightStick XPP-5422GM