Contents - Table Of Contents
- Table Of Contents
- GENERAL INFORMATION
- SAFETY
- TECHNICAL DATA (SCRUBTEC 545B, 545BL, 553B, 553BL, BOOST 5)
- TECHNICAL DATA (SCRUBTEC 653B, 653BL, 651BCL, 661BL)
- TECHNICAL DATA (SCRUBTEC 545E, 553E, 653E)
- MAINTENANCE
- MACHINE NOMENCLATURE (SCRUBTEC 545B, 545BL, 553B, 553BL, BOOST 5)
- MACHINE NOMENCLATURE (SCRUBTEC 653B, 653BL, 651BCL, 661BL)
- MACHINE NOMENCLATURE (SCRUBTEC 545E, 553E)
- MACHINE NOMENCLATURE (SCRUBTEC 653E)
- SOLUTION/CLEAN WATER SUPPLY SYSTEM
- SOLUTION FILTER CLEANING (SCRUBTEC 653B, 653BL, 651BCL, 661BL, 653E)
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (SCRUBTEC 545B, 545BL, 553B, 553BL, BOOST 5, 545E, 553E)
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (SCRUBTEC 653B, 653BL, 651BCL, 661BL, 653E)
- TROUBLESHOOTING
- CHEMICAL MIXING SYSTEM
- BRUSHING SYSTEM
- BRUSH/PAD-HOLDER DECK DISASSEMBLY/ASSEMBLY (SCRUBTEC 545E, 553E, 653E)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 545B, 545BL, 553B, 553BL, BOOST 5)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 653B, 653BL)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 651BCL)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 661BL)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (SCRUBTEC 545B, 545BL, 553B, 553BL)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (SCRUBTEC 653B, 653BL)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (SCRUBTEC 651BCL)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (SCRUBTEC 661BL)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (SCRUBTEC 545B, 545BL, 553B, 553BL, 653B, 653BL)
- BOOST DECK MOTOR DISASSEMBLY/ASSEMBLY (SCRUBTEC BOOST 5)
- BOOST DECK VIBRATION-DAMPERS DISASSEMBLY/REPLACEMENT (SCRUBTEC BOOST 5)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (SCRUBTEC 651BCL)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (SCRUBTEC 661BL)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (SCRUBTEC 545E, 553E, 653E)
- RECOVERY WATER SYSTEM
- SQUEEGEE CLEANING/CHECK/REPLACEMENT AND SQUEEGEE BLADE REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR FILTER CLEANING (All models)
- VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 545E, 553E, 653E)
- VACUUM SYSTEM MOTOR CARBON BRUSH CHECK/REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY (All models)
- SQUEEGEE SPRING CHECK/REPLACEMENT (All models, with aluminium squeegee)
- DRIVE SYSTEM
- DRIVE SYSTEM MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 545BL, 553BL, BOOST 5, 653BL, 651BCL, 661BL)
- drive system electronic board diagnostic table
- OTHER SYSTEMS
- ELECTRICAL SYSTEM
- BATTERY TYPE SETTING (WET OR GEL) (SCRUBTEC 545B, 553B, 653B)
- BATTERY TYPE SETTING (WET OR GEL) (SCRUBTEC 545BL, 553BL, BOOST 5, 653BL, 651BCL, 661BL)
- FUSE CHECK/REPLACEMENT (SCRUBTEC 545B, 545BL, 553B, 553BL, BOOST 5, 653B, 653BL, 651BCL, 661BL)
- FUSE CHECK/REPLACEMENT (SCRUBTEC 545E, 553E, 653E)
- WATER FLOW CONTROL ELECTRONIC BOARD DISASSEMBLY/ASSEMBLY (SCRUBTEC 545E, 553E, 653E)
- COMPONENT LAYOUT (SCRUBTEC 545B, 553B, 653B)
- WIRING DIAGRAM (SCRUBTEC 545B, 553B, 653B)
- COMPONENT LAYOUT (SCRUBTEC 545BL, 553BL, BOOST 5, 653BL, 651BCL, 661BL)
- WIRING DIAGRAM (SCRUBTEC 545BL, 553BL, BOOST 5, 653BL, 651BCL, 661BL)
- COMPONENT LAYOUT (SCRUBTEC 545E, 553E, 653E)
- WIRING DIAGRAM (SCRUBTEC 545E, 553E, 653E)
| 
62 SCRUBTEC 545B / 545BL / 553B / 553BL / BOOST 5653B / 653BL / 651BCL / 661BL / 545E / 553E / 653E 9097062000(2)2009-06ENGLISH SERVICE MANUALRECOVERY WATER SYSTEMVACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK (SCRUBTEC 545B, 545BL, 553B, 553BL,BOOST 5, 653B, 653BL, 651BCL, 661BL)WARNING!This procedure must be performed by qualified personnel only.If the tank (21) contains recovery water:1.Drive the machine to the appointed recovery water disposal area.Turn the ignition key (80) to “0”.Empty the recovery water tank (21) with the hose (16).Drive the machine on a level floor.2.Turn the ignition key (80) to “0”.3.Disconnect the battery connector (12).4.Carefully lift the tank (40).5.Apply the amperometric pliers (A) on one cable (B) of the batteries.6.Turn the ignition key (80) to “I”.7.Turn on the vacuum system by pressing the switch (73) and check that the motor electrical input is 16 - 19 A at 24 V.8.Turn off the vacuum system motor by pressing the switch (73).Remove the amperometric pliers (B).If the electrical input exceeds the specifications, check the motor carbon brushes (see the procedure in the relevantparagraph).If necessary, disassemble the vacuum system motor (see the procedure in the relevant paragraph), and check the condition ofits moving parts.If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced (see the procedure inthe relevant paragraph).Perform steps 4 and 5 in the reverse order.9.BAS301553 |
