Security settings for wireless LAN access pointsSelect Menu > Tools > Settings > Connection > Access points. Select Options > New access point and start to create a wirelessLAN access point, or select a wireless LAN access point and Options > Edit.WEP security settingsIn the access point settings, select WLAN security mode > WEP.Wired equivalent privacy (WEP) encryption method encrypts data before it is transmitted. Access to the network is denied tousers who do not have the required WEP keys. When WEP security mode is in use, if your device receives a data packet notencrypted with the WEP keys, the data is discarded.In an Ad-hoc network, all devices must use the same WEP key.Select WLAN security sett. and from the following:• WEP key in use — Select the desired WEP key.• Authentication type — Select Open or Shared.• WEP key settings — Edit the settings for the WEP key.WEP key settingsIn the access point settings, select WLAN security mode > WEP.In an Ad-hoc network, all devices must use the same WEP key.Select WLAN security sett. > WEP key settings and from the following:• WEP encryption — Select the desired WEP encryption key length.• WEP key format — Select whether you want to enter the WEP key data in ASCII or Hexadecimal format.• WEP key — Enter the WEP key data.802.1x security settingsIn the access point settings, select WLAN security mode > 802.1x.802.1x authenticates and authorizes devices to access a wireless network, and prevents access if the authorization process fails.Select WLAN security sett.. and from the following:• WPA mode — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).• EAP plug-in settings — If you selected WPA mode > EAP, select which EAP plug-ins defined in your device to use with theaccess point.• Pre-shared key — If you selected WPA mode > Pre-shared key, enter the shared private key that identifies your device tothe wireless LAN to which you connect.The settings available for editing may vary.WPA security settingsIn the access point settings, select WLAN security mode > WPA/WPA2.Select WLAN security sett.. and from the following:• WPA mode — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).• EAP plug-in settings — If you select WPA mode > EAP, select which EAP plug-ins defined in your device to use with the accesspoint.• Pre-shared key — If you select WPA mode > Pre-shared key, enter the shared private key that identifies your device to thewireless LAN to which you connect.The settings available for editing may vary.EAPTo view the EAP (extensible authentication protocol) plug-ins currently installed in your device (network service), select Menu >Tools > Settings > Connection > Access points. Select Options > New access point and define an access point that useswireless LAN as a data bearer and 802.1x or WPA/WPA2 as the security mode. Select WLAN security sett. > WPA mode > EAP,scroll to EAP plug-in settings, and press the scroll key.The extensible authentication protocol (EAP) plug-ins are used in wireless networks to authenticate wireless devices andauthentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service).To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and Options > Enable.The EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select Options >Disable.To edit the EAP plug-in settings, select Options > Configure.To change the priority of the EAP plug-in settings, select Options > Raise priority to attempt to use the plug-in before otherplug-ins when connecting to the network with the access point, or Options > Lower priority to use this plug-in for networkauthentication after attempting to use other plug-ins.The available options may vary.S e t t i n g s© 2007 Nokia. All rights reserved. 84
