Nordica INSERTO 70 Crystal Angolo DX Instructions For Installation, Use And Maintenance Manual

Also see for INSERTO 70 Crystal Angolo SX: Instructions for installation, use and maintenance Instructions for installation, use and maintenance

Contents

Nordica INSERTO 70 Crystal Angolo DX Instructions For Installation, Use And Maintenance Manual Manual pdf 15 page image

1. GENERAL PRECAUTIONSLa NORDICA S.p.A. responsibility is limited to the supply of the appliance.The installation must be carried out scrupulously according to the instructions provided in this manual and the rules of the profession.Installation must only be carried out by a qualified technician who works on behalf of companies suitable to assume the entire responsibilityof the system as a whole.La NORDICA S.p.A. declines any responsibility for the product that has been modified without written authorisation as well asfor the use of non-original spare parts.This appliance is not suitable for the use of inexperienced people (included children) or with physical, sensorial and mental reducedcapacities. They have to be controlled and educated in the use of the appliance from a responsible person for their security. The childrenhave to be controlled to be sure that they would not play with the appliance. (EN 60335-2-102/7.12).It is OBLIGATORY to respect the National and European rules, local regulations concerning building matter and also fireproofrules.NO MODIFICATIONS CAN BE CARRIED OUT TO THE APPLIANCE. La NORDICA S.p.A. cannot be held responsible for lack ofrespect for such precautions.2. INSTALLATION REGULATIONSInstallation of the product and auxiliary equipment in relation to the heating system must comply with all current Standards and Regulationsand to those envisioned by the law.The installation and the relating to the connections of the system, the commissioning and the check of the correct functioning mustbe carried out in compliance with the regulations in force by authorised professional personnel with the requisites required by the law,being national, regional, provincial or town council present in the country within which the appliance is installed, besides these presentinstructions.Installation must be carried out by authorised personnel who must provide the buyer with a system declaration of conformity and willassume full responsibility for final installation and as a consequence the correct functioning of the installed product.Before installing the appliance, carry out the following checks:• Make sure that the floor can support the weight of the appliance, and if it is made of flammable material, provide suitable insulation(DIMENSIONS ACCORDING TO REGIONAL REGULATIONS). With a flammable floor the appliance must be installed on a12 cm thick stone or concrete slab.• Make sure that there is adequate ventilation in the room where the appliance is to be installed.• Do not install the appliance in rooms containing collective ventilation ducts, hoods with or without extractor, type B gas appliances,heat pumps, or other appliances that, operating at the same time, can put the room in depression (ref. UNI 10683 standard)• Make sure that the flue and the pipes to which the appliance will be connected are suitable for its operation. It is NOT allowed theconnection of various appliances to the same chimney.• The diameter of the opening for connection to the chimney must at least correspond to the diameter of the flue gas pipe. Theopening must be equipped with a wall connection for the insertion of the exhaust pipe and a rosette.• Always leave the recommended air pocket between the appliance and the walls, rear and side min. (see MARKING INFORMATION).• Establish the type of ventilation (natural or forced) see chapter VENTILATION HOOD OR ADJACENT LOCAL.• By means of the adjustable feet and using a level make sure that the device is perfectly levelled to allow a correct sliding of the door.After testing the proper working of the appliance, some days from the installation, it is possible to proceed with the constructionof its aesthetic covering.WARNING: During the surround building operations it must kept in mind possible and subsequent electrical installed parts maintenance(Fans, temperature probe, etc) and with hydraulic systems all parts connected to the product.La NORDICA S.p.A. declines all responsibility for damage to things and/or persons caused by the system. In addition, it is notresponsible for any product modified without authorisation and even less for the use of non original spare parts.Your regular local chimney sweep must be informed about the installation of the appliance so that he can check the correct connection tothe chimney.3. FIRE-FIGHTING SAFETY MEASURESWhen installing the appliance, the following safety measures must be observed:a) In order to ensure sufficient thermal insulation, respect the minimum safety distance from objects or furnishing components flammableand sensitive to heat and from materials with flammable structure (see CE MARKING INFORMATION). All the minimum safetydistances are shown on the product data plate and lower values must not be used.b) in front of the furnace door, in the radiation area, there must be no flammable or heat-sensitive objects or material at a distance ofless than 80 cm. This distance can be reduced to 40 cm where a rear-ventilated, heat-resistant protection device is installed in frontof the whole component to protect;c) If the product is installed on a no totally refractory floor, one must foresee a fireproof background. The floors made of inflammablematerial, such as moquette, parquet or cork etc., must be replaced by a layer of no-inflammable material (size according toregional law) In case the replacement of the floor is not possible, the appliance shall be placed on a minimum 12 cm thickslab made of stone or concrete (see Picture 1 at page 40).INSERTO 70 CRYSTAL ANGOLO16 6096705 - IT-EN-DE-FR