Nordica Monoblocco Piano 600 Instructions For Installation, Use And Maintenance Manual

Contents

Nordica Monoblocco Piano 600 Instructions For Installation, Use And Maintenance Manual Manual pdf 9 page image

device is properly heated and lets it stop when the fan is partially cold.The lighting and the adjustment is carried out through the proper standard supplied control unit that has to be installed far from any directheat source.CONNECTION (Picture 14 at page 44):Connect the feeding cable of the switchboard with an electronic bipolar switch respecting at least a 3 mm distance between the contacts(power supply 230V~ 50 Hz, it is necessary to provide for the correct connection to the grounding plant).WARNING: The COMMAND must be connected to the mains with a differential line cut-off switch according to the regulations in force.Correct operation of the command is assured only for the proper motor for which it has been manufactured. Improper use relieves themanufacturer from each responsibility.8. ALLOWED / NOT ALLOWED FUELSAllowed fuels are logs. Use exclusively dry logs (max. content of water 20%). Maximum 3 logs should be loaded. The pieces of woodshould have a length of ca. 20-30 cm and a maximum circumference of 30-35 cm.Compressed not worked-out wood briquettes must be used carefully to avoid overheating that may damage the device, sincethese have a very high calorific value.The wood used as fuel must have a humidity content lower than the 20% and must be stored in a dry place. Humid wood tends to burnless easily, since it is necessary a greater quantity of energy to let the existing water evaporate. Moreover, humid content involvesthe disadvantage that, when temperature decreases, the water condensates earlier in the hearth and therefore in the stack causing aremarkable deposit of soot with following possible risk of fire of the same.Fresh wood contains about 60% of H2O, therefore it is not suitable to be burnt.It is necessary to place this wood in a dry and ventilated place (for example under a roofing) for at least two years before using it.Besides others, it is not possible to burn: carbon, cuttings, waste of bark and panels, humid wood or wood treated with paints,plastic materials; in this case, the warranty on the device becomes void.Paper and cardboard must be used only to light the fire.The combustion of waste is FORBIDDEN and would even damage the appliance and the flue, causing health damages and claims bythe neighborhood owing to the bad smell. The wood is not a fuel which allows a continuous operation of the appliance, as consequencethe heating all over the night is not possible.Variety Kg/mc kWh/kg moistness 20%Beech 750 4,0Oak 900 4,2Elm 640 4,1Poplar 470 4,1Larch* 660 4,4Spruce* 450 4,5Scots pine * 550 4,4* RESINOUS WOOD NOT SUITABLE FOR THE BURNINGATTENTION : the continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages the cast iron parts(cleavage) of the product.9. LIGHTINGAfter the first ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) which disappear aftera brief using of the appliance. A good ventilation of the room should always be guaranteed.T light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means.It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.Open the primary air completely.When wood starts to burn, it is possible to feed it again by opening slowly the door, in order to avoid leaks of smoke, and close theprimary air register and control the combustion through the secondary air register according to the provisions of chapter TECHNICALDESCRIPTION. Please always be present during this phase.Never overload the appliance (see the technical table - max. quantity of fuel that can be loaded / hourly consumption).Too much fuel and too much air for combustion can cause overheating and therefore damage the same.Never switch on the device when there are combustible gases in the room.To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following information:• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,refractory material and majolica;• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures withinthe range of 300°C - 500°C are detected;MONOBLOCCHI 600 - 750 - 9006098700 - IT-EN-DE-FR 19