Nordica TERMOCAMINO Series User Manual

Contents

Nordica TERMOCAMINO Series User Manual Manual pdf 12 page image

ENgLIsHVariety kg/mc kWh/kg moistness 20%Poplar 470 4,1Larch* 660 4,4spruce* 450 4,5scots pine * 550 4,4* RESINOUS WOOD NOT SUITABLE FOR THE BURNINGATTENTION : the continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages thecast iron parts (cleavage) of the product.The declared technical data have been achieved by burning beech wood class “A1” according to the requirement UNI EN ISO 17225-5 and woodmoisture content less than 20%. By burning a different kind of wood the efficiency of the product itself could change and some specific adjustmentson the appliance could be needed.LIgHTINgATTENTION: never light for any reason if the installation is not completely full of water in order to avoid a serious damageof the whole structure. IABsOLUTELY DO NOT LIgHT THE FIRE IN THE THERMO-FIREPLACE IN THE TOTAL OR PARTIALABsENCE OF WATER (NOT EVEN FOR CHECKING), AS IT COULD BE IRREMEDIABLy RUINED. IN SUCH CASE THE WARRANTy ON THEAPPLIANCE IS VOIDED.Before installing the facing and lighting the thermo-fireplace, it must be loaded and the system filled from the open expansion tank by meansof the natural fall of the water (see chapter. SySTEM CONNECTION AND FILLING).After ensuring that at least one radiator is always open, open the door and load a small quantity of wood.To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means.It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar. Never switch on the device whenthere are combustible gases in the room.The openings for air (primary and secondary) must be opened together (you must open the eventual Ignition control, and butterfly valveplaced on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for combustion accordingto the instructions on paragraph TECHNICAL DESCRIPTION.Please always be present during this phase. Never overload the appliance (see cap. TECHNICAL DESCRIPTION - Hourlyconsumption). Too much fuel and too much air for combustion can cause overheating and therefore damage the same.After the first ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) whichdisappear after a brief using of the appliance. A good ventilation of the room should always be guaranteed.ATTENTION: during the first lightings there could be a solid smokes condensation with a small escape of water from thethermo-fireplace: this event will expire in a very short time but if it persists it will be necessary to check the chimneydraught.To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following information:• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,refractory material and majolica;• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within therange of 300°C - 500°C are detected;• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use orof absolute standstill when season changes;• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to completethe various elastic stresses;• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint. Thispaint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of time thetemperature of 350 °C before becoming completely embedded in the metallic surfaces.Therefore, it is extremely relevant to take these easy steps during the lighting:1. Make sure that a strong air change is assured in the room where the appliance is installed.2. During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) andkeep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions manual.3. Repeat this operation for at least 4-5 or more times, according to your possibilities.4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) and,if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.5. During the first starts, no object should be leaned on the appliance and in detail on enamelled surfaces. Enamelled surfaces must not betouched during heating.29