Nordica TERMOCAMINO Series User Manual

Contents

Nordica TERMOCAMINO Series User Manual Manual pdf 13 page image

ENgLIsH6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessiveloads. After testing the proper working of the appliance, some days from the installation, it is possible to proceed with theconstruction of its aesthetic covering.WARNINg: During the surround building operations it must kept in mind possible and subsequent electrical installed partsmaintenance (Fans, temperature probe, etc) and with hydraulic systems all parts connected to the thermo-fireplace.LOW EMIssION FIRE LIgHTINgSmokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns graduallyfrom the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the flame andtherefore burn almost completely.Place the logs in the hearth a certain distance apart as shown in the Picture 15. Arrange the largest at the bottom and the smallest at thetop, or vertically in the case of tall narrow combustion chambers. Place the fire starter module on top of the pile, arranging the first logs in themodule at right angles to the pile of wood.Fire sTARTER MODULE. This fire starter module replaces a paper or cardboard starter. Prepare four logs, 20 cm long with a cross section of 3cm by 3 cm Picture 15. Cross the four logs and place them on top of the pile of wood at right angles, with the fire lighter (wax impregnatedwood fibre for example) in the middle. The fire can be lit with a match. If you want, you can use thinner pieces of wood. In this case, you willneed a larger quantity. Keep the flue gas exhaust valve and combustion air regulator open.After lighting the fire, leave the combustion air regulator open in the position shown in the Picture.IMPORTANT:• do not add further wood between one complete load and the next;• do not suffocate the fire by closing the air intakes;• regular cleaning by a chimney sweep reduces fine particle emissions.these instructions are backed by ENERGIA Legno SVIZZERA www.energia-legno.chNORMAL OPERATIONAfter having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses anddeformations.You should always use the product with the door closed in order to avoid damages due to overheating (forge effect). Theinobservance of this rule makes the warranty expire.IMPORTANT: For safety reasons the door of the hearth can be opened only for the loading of the fuel. The hearth door mustalways remain closed during operation or rest.With the registers located on the front of the device, it is possible to adjust the heat emission of the same. They have to be opened according tothe calorific need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air for combustionflows through the secondary air register.Never overload the appliance. Too much fuel and too much air for the combustion may cause overheating and then damage theproduct. you should always use the appliance with the door closed in order to avoid damages due to overheating (forge effect).The adjustment of the registers necessary to reach the rated calorific yield is the following one: see chap. TECHNICAL DESCRIPTION. Theappliance works as an intermittent operating appliance.In the event that the water temperature exceeds the tripping temperature of the safety devices, immediately suspend thefeeding of wood, and make sure that the water temperature and the flame decrease, eliminating the causes of theoverheating (if necessary by closing the air register). If the water system is connected in the thermo-fireplace, the hot watertap can be opened to speed up the cooling of the appliance.Besides the adjustment of the air for the combustion, the intensity of the combustion and consequently the thermal performance of thedevice is influenced by the stack. A good draught of the stack requires a stricter adjustment of air for combustion, while a poor draughtrequires a more precise adjustment of air for combustion.To verify the good combustion, check whether the smoke coming out from the stack is transparent.If it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that thecombustion is not complete (it is necessary a greater quantity of secondary air).WARNINg: When fuel is added onto the embers in the absence of a flame, a considerable amount of fumes may develop. Shouldthis happen, an explosive mixture of gas and air may form, and in extreme cases an explosion may occur. For safety reasons it isadvisable to perform a new lighting procedure with the use of small strips.ELECTRICAL POWER sUPPLY FAILUREIn the event of an unexpected electrical power supply failure during normal system operation, it will be necessary to carry out these simplemanoeuvres to prevent the water in the boiler starting to boil as a consequence of the lack of pump operation.• Close completely the primary and secondary air registers in order to smother the flame as much as possible.• Close the smokes register, if existing, to limit further coming of combustive air through possible cracks.30