Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Nortel BCM50 Release 3.0 SIP Configuration Manual

Also see for BCM50: Configuration guideInstallation and maintenance guideKeycode Installation GuideIntegration guideInstallation and configuration guide

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Contents
  1. configuration guide
  2. Table Of Contents
  3. Table Of Contents
  4. Introduction
  5. Trouble Reporting
  6. Special Notes
  7. Overview
  8. Configuration Guide
  9. Figure 3: BCM50 Lists of Applied Patches
  10. IP Trunks
  11. Figure 4: Available VoIP Trunks
  12. Figure 6: Assigning Line Pool to IP Trunks
  13. Figure 8: Configuring General DN Length
  14. Figure 10: Configuring Private Received Number Length
  15. Figure 11: Assigning a Route for IP Trunks
  16. Figure 12: Assign Code to Access IP Trunk Routes
  17. SIP Proxy Parameters
  18. Figure 15: Outbound Proxy Table for failover to secondary AT&T IPBEs
  19. Media Parameters
  20. Figure 17: Configuring analog DNs for fax
  21. Port Ranges
  22. Configuring Outgoing Calls from BCM50 to AT&T IP Flex Reach
  23. Configuring Incoming Calls from AT&T IP Flex Reach to BCM50
  24. Figure 21: Display DID on IP Set LCD
  25. Figure 22: Assign Line Pool to IP Sets
  26. Troubleshooting
  27. Figure 24: IP Device Listing
  28. Figure 25: RTP Session Information
  29. Figure 27: System Resources
  30. Real-time display of BCM50 Alarms
  31. Log Management
  32. APPENDIX A: Configuring Destination Code with Wildcard
Nortel BCM50 Release 3.0 SIP Configuration Manual Manual pdf 24 page image
AT&T IP Flexible Reach ServiceNortel BCM50 Release 3.0 SIP Configuration Guide© 2007 AT&T Intellectual Property. All rights reserved. AT&T, the AT&Tlogo and all other AT&T marks contained herein are trademarks of AT&TIntellectual Property and/or AT&T affiliated companies. All othermarks contained herein are the property of their respective owners.DN used the analog device and go to the “Capabilities and Preferences” tab.On the lower navigation section, select “ATA Settings” and set the “ATAdevice” to “Modem.”Figure 17: Configuring analog DNs for faxFor T.38 fax requirements, ensure that the “ATA device” is set to “Telephone.”Issue 0.7 Page 24 of 37
/ 37
Related manuals for Nortel BCM50
Nortel Meridian 1 Succession 1000M Installation And Configuration Manual first page preview
Nortel Meridian 1 Succession 1000M Installation And Configuration Manual
Nortel Meridian 1 Succession 1000M Installation And Configuration Manual first page preview
Nortel Meridian 1 Succession 1000M Installation And Configuration Manual
Nortel Meridian Companion Operation Manual first page preview
Nortel Meridian Companion Operation Manual
Nortel IW SPM IP Manual first page preview
Nortel IW SPM IP Manual
Nortel Meridian Companion Reference Manual first page preview
Nortel Meridian Companion Reference Manual
Nortel Meridian Companion Reference Manual first page preview
Nortel Meridian Companion Reference Manual
Nortel Meridian Mail Release Note first page preview
Nortel Meridian Mail Release Note
Nortel Meridian Meridian 1 Installation Manual first page preview
Nortel Meridian Meridian 1 Installation Manual
Nortel Meridian Meridian 1 Release Note first page preview
Nortel Meridian Meridian 1 Release Note
Nortel Meridian Meridian 1 Implementation Manual first page preview
Nortel Meridian Meridian 1 Implementation Manual
This manual is suitable for:
BCM50
Manuals database logo
manualsdatabase
Your AI-powered manual search engine