Contents - Standard 17.00 January
- Return
- Space or
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Removing module covers and pedestal grills
- NT1P61 Fibre Superloop Network Card
- NT1P62 Fibre Peripheral Controller Card
- NT4N43 cPCI Multi-Media Disk Unit
- NT4N65, and NT4N66 cPCI Core Network Interface Cards
- NT4N67 and NT4N68 System Utility cards
- CP PII) card
- NT5D10 68060 Call Processor (CP) Card
- NT5D12AA Dual DTI/PRI (DDP)
- Installing the DDP card
- NT5D20 IOP/CMDU cards or NT6D63 IOP and NT6D64 CMDU cards replaced with NT5D61 IODU/C cards
- Splitting the cores
- Replacement procedure for Option 51C systems
- Completing the upgrade
- NT5D61 Input/Output Disk Unit with CD-ROM (IODU/C)
- Replacing the IODU/C in a redundant system
- Replacing the IODU/C in an Option 51C
- NT5D61 IODU/C Security Device
- Replacing the Security Device on a redundant system
- Replacing the Security Device on an Option 51C system
- NT5D2103 Core/Network Card Cage
- NT5K09 Quad Digitone Receiver
- NT5K10 Dual Loop Peripheral Buffer Card
- NT5K1106 Enhanced Peripheral Equipment Card Cage
- Sender/Receiver Card
- NT6D40, NT6D41, NT6D42, Power Supply DC
- NT6D65 and NTRB34 Core to Network Interface Cards
- NT7D10 Power Distribution Unit DC
- NT7D67CB Power Distribution Unit DC
- NT7R51 Local Carrier Interface Card
- NT7R52 Remote Carrier Interface Card
- NT8D01 Controller Card
- Intelligent Peripheral Equipment Card
- NT8D04 Superloop Network Card, QPC414 Network Card
- NT8D06, NT8D21, NT8D29 Power Supply AC
- NT8D17 Conference/TDS Card
- NT8D22 System Monitor
- NT8D41 Dual or Quad Port Serial Data Interface card
- NT8D46AC Thermostat Harness
- NT8D46AM, NT8D46DC Air Probe Harness
- NT8D52AB, NT8D52DD Pedestal Blower Unit
- Power Distribution Unit
- NT8D3503/NT8D3507 Network Module Card Cage
- Connect groups 1 through 7: shelf 0 to shelf 1
- Connect the Network modules to the Core/Net modules
- cCNI slot and port assignments
- cCNI to 3PE Termination Panel cable connections
- NT8D3703 IPE Module Card Cage
- systems equipped with NT5D61 IODU/C cards
- NTAG26 Extended Multi-frequency receiver
- NTBK51AA Downloadable D-Channel Daughterboard
- Installing the DDCH Daughterboard
- NTRB33 Fiber Junctor Interface card
- P0699798 Air Filter
- QPC43 Peripheral Signaling Card
- QPC441 Three-Port Extender Card
- QPC471, QPC775 Clock Controller Card
- QPC477 Bus Terminating Unit
- QPC659 Dual Loop Peripheral Buffer Card
- QPC841 Serial Data Interface Card
- NT7D67CB PDU
- Index
|
Replacing equipment Page 107 of 250Hardware Replacement10 Select to confirm.11 Select to confirm the software release to be copied.12 When the software is installed successfully, press to installCP-software from the hard disk to Flash EEPROM, and installCP-BOOT ROM. Follow the screen directions until the Main Menureturns.13 When the Main Menu returns, select to install IOP-ROM.Nortel Meridian - 1 Software/Database/PEROM CDROM INSTALL Tool (x11)You selected to copy the hard disk /p partition from IODU on Core 1to IODU on Core 0.60 MB of disk will be copied.This wil erase old system files, Database files will NOT be erased.Note that ERASED FILES CANNOT BE RECOVERED.NOTE: Copy progress will be indicated by ... , one '.' per MB.You may Continue with the copy operation or Quit nowand leave your system unchanged.Please enter: -Copy /p partition from one Core 1 to Core 0. - Quit. Enter Choice > a-->553-7739— — — — — — — — — — — — — — — — — — — — — —— — — — — — — — — — — — — — — — — — — — — —Nortel Meridian - 1 Software/Database/PEROM CDROM INSTALL Tool (x11)Release: xxxx was installed successfully into /p partitionon your sideNOTE: In order to complete the install you must install flash ROMIn order to complete the install you must install CP BOOT ROMPlease press when ready... 553-7741— — — — — — — — — — — — — — — — — — — — — —— — — — — — — — — — — — — — — — — — — — — — PreviousNext |