Staple unitScrewsFront cabinetParts included1. Turn off the main switch of the main unit of the printer.2. Remove the front cover from the right front of the finisher.Turn the main switch locatedon the front side of the mainunit to the "OFF" position.Then remove the power plugof the main unit from the outlet.Loosen the screw and removethe connector of the finisher."OFF"Screw(M4 x 6 with rosette): 1 pc.Harness A (purple): 1 pc. Harness B (orange): 1 pc.Dust box label:1 sheet<1> Remove the four top coversecuring screws and remove the topcover.8. Reattach the front cover to the right front of the finisher.7. Reattach the covers that have been removed.6. Connect the harness of the punch module to the PWBof the finisher.5. Attach the punch module.4. Remove the top cover.Installation is now complete.Screws BScrews AFront cover<3> Remove the three screwsthat fix the rear cabinet andremove the rear cabinet.At this time, remove the relayharness through the openingof the rear cabinet.<1> Open the frontdoor of the finisher andremove the jamhandling dial.3. Remove the front cabinet and the rear cabinet fromthe finisher.Jam handling dialStaple unitScrewsScrewsFront cabinetScrewRelay harnessOpening forrelay harnessScrewRearcabinetScrewRelay harnessOpening forrelay harnessScrewsRear cabinet<2> Remove the four pawlsfrom the top cover andseparate the cover into theupper and lower portions.Reuse the upper portion.Top coverLock release lever (A)Projection (B)Latch arm Pawl (D)Screw ScrewTop coverFor installation of B83THP / USP / FHP / FBP, a saddle stitchfinisher B83SS must have been installed.<2> Remove the four frontcabinet securing screws, pullout the staple unit until it stops,then remove the pawl of thefront cabinet in the directionindicated by the arrow andremove the front cabinet.<4> Remove the three rearcabinet securing screws,remove the pawl in thedirection indicated by thearrow, and remove the rearcabinet.At this time, remove the relayharness through the openingof the rear cabinet.ScrewsConnectorAC cordHole punch position label:2 sheetsScrewsConnectorPawlPawl9. Paste the dust box label to the top cover.Remove the clamps that fixthe harness, handle the wiringof harness A (purple) andharness B (orange), and fixthem with the clamps.Paste the supplied dust boxlabel to the location indicatedin the illustration.<1> Insert the two bosses of the punch unit into the boss holes of thefinisher and fix the punch module using three screws.(Note)For the screws, use a supplied screw and the two screws that have beenremoved in step 4.Top coverScrewsBossBoss holeBossBoss holeScrew (with rosette) (supplied with this module)ScrewScrewPunch module<4> Reattach the jamhandling dial and close thefront cover.ClampsClampsHarness A (purple)Harness B (orange)Harness A (purple)Harness B (orange)Jam handling dialB83THP / USP / FHP / FBPInstallation ManualFOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.SEE OKI DIGITAL PRINTER SERVICE MANUAL ORINSTALLATION MANUAL TO DETERMINE SUITABILITY.10. Connect the connector to the stand/paper drawer andconnect the AC cord of the power supply unit to themain unit of the printer.Connect the connector of therelay harness of the finisher tothe stand/paper drawer andtighten the screws of theconnector.(C)Remove the screws A and B(two for each) that secure thefinisher front cover andremove the front cover.Screws BScrews AFront coverPawlPawl<1> Hang the two pawls ofthe top cover and securethem using the two screws.<2> Pass the relay harness tothe rear cabinet and securethe rear cabinet using thethree screws.<3> Remove the lock releaselever that has been attachedto the front cabinet.Reattach the front cabinet toits original position, push inthe staple unit, and attach itusing the two screws.Insert the protrusion (B) of thelock release lever that hasbeen removed before to thehole (C) of the latch arm.After attaching it, move thelever to check that it movessmoothly.If the lever does not movesmoothly, remove the lockrelease lever by releasing thepawl at the lower part of thelock release lever using a flat-blade screwdriver or the likeand then insert it again.Attach the front cover usingthe screws A and B (two foreach).Pawl12
