PAC HFS Connecting Manual
  |
IntroductionThank you for purchasing the PAC HFS Bluetooth phone kit integration module. The HFS was designed to seam-lessly integrate the Motorola IHF1000 Bluetooth phone kit into your vehicle’s audio system. The HFS is completelyPlug-n-Play and does not require any cutting or splicing of wires when used with the Motorola Z02 harness. Thevehicle specific harnesses plugs directly into the vehicle’s audio system. When the IHF1000 is activated by eitheran incoming or outgoing call, the HFS will automatically mute the audio system and uses the front speakers toprovide the audio for the hands free conversation. The HFS is a speaker level audio switcher that is designed fornon- amplified audio systems and is not recommended for some factory amplified audio systems.Back of Radio Factory Radio HarnessHFSIHF 1000InstallationImportant Note: The IHF1000 you are installing will have one of two different style main harnesses. Installation willvary depending upon harness style. The harness that comes with the IHF1000 will have a sticker on it with a partnumber. The last three characters of the part number will be either ZO1 or ZO2. The HFS is designed to be Plug-n-Play compatible with the ZO2 harness. If your IHF1000 comes with a ZO1 harness, you will be required to makewire connections from the HFS to the ZO1 harness. Please follow the appropriate instructions below for yourparticular situation.Connections with the ZO2 harnessNote: All connections to the vehicle for power and audio are made with the vehicle specific harness for HFS. Do notconnect any wires from the IHF1000 directly to the vehicle. All connections will be made between the IHF1000harnesses and the P-M2UP harness. You will need to mount the UIM and the Microphone that comes with theIHF1000. These components plug directly into both the ZO1 and ZO2 Motorola harnesses.CAUTION!!!! Make certain that you have the radios security code if the radio has one. The radio may require thesecurity code to operate after being plugged in.Connection at Radio.1. Unplug the factory harness from the radio.2. Plug the factory Harness into the Vehicle side of the PAC harness.3. Plug the Radio side of the harness into the factory radio.4. Connect the 18 pin connector from the vehicle specific harness to the Vehicle Interface side of the HFS.5. Connect the 16 pin connector on the P-M2UP into the Phone Interface side of the HFS.6. Connect the 8 pin connector to the Motorola ZO2 harnessVehicle Specific HarnessRadio Side Vehicle SideP-M2UP18 Pin vehicle connectorMore on BackBluetooth Phone KitIntegration Modulewww.pac-audio.comHands Free SwitcherMODEL # HFSSpeaker Level Audio Switcher for theMotorola IHF1000 Bluetooth Phone Kit Pacific Accessory Corpo-Connections with the ZO1 harnessIf your Motorola IHF1000 Bluetooth phone kit came equipped with the ZO1 harness, you will not be able to plug theHFS directly into the Motorola harness. In this case you will need to make some wire connections.Wiring Connections1. Cut off the white 8 pin connector from the P-M2UP harness.2. Cut off the 2 pin connector for the speaker.3. Connect the BLACK wire from the speaker plug to the PURPLE wire on the P-M2UP harness.4. Connect the YELLOW wire from the speaker plug to the GREY wire on the P-M2UP harness.5. Connect the RED wire from the ZO1 harness to the RED wire on the P-M2UP harness.6. Connect the GREEN wire from the ZO1 harness to the GREEN wire on the P-M2UP harness.7. Connect the BLACK wire from the ZO1 harness to the BLACK wire on the P-M2UP harness.8. Connect the YELLOW wire from the ZO1 harness to the YELLOW wire on the P-M2UP harness.CAUTION!!!! Make certain that you have the radios security code if the radio has one. The radio may require thesecurity code to operate after being plugged in.Connection at Radio.1. Remove the factory harness from the radio.2. Plug the factory Harness into the Vehicle side of the PAC harness.3. Plug the Radio side of the harness into the factory radio.4. Connect the 18 pin connector from the vehicle specific harness to the Vehicle Interface side of the HFS.5. Connect the 16 pin connector on the P-M2UP into the Phone Interface side of the HFS.MODEL # HFSSpeaker Level Audio Switcher for theMotorola IHF1000 Bluetooth Phone KitBack of Radio Factory Radio HarnessIHF 1000Vehicle Specific CelFi™HarnessRadio Side Vehicle SideP-M2UP18 Pin vehicle connectorMake wire connections HereHFSBluetooth Phone KitIntegration Modulewww.pac-audio.comHands Free SwitcherPacific Accessory Corpo-Pacific Accessory Corporation1340 Ritchey St.Santa Ana, CA 92705techsupport@pac-audio.comwww.pac-audio.com • Ph: 866-931-8021© 2009 Pacific Accessory Corporation |
Related manuals for PAC HFS
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine