PAC SRK-JW18EH Manual

Also see for SRK-JW18EH: Install manual

Stinger HEIGH10™ Radio Replacement Kitfor Jeep Wrangler JL and Jeep Gladiator JT VehiclesSRK-JW18EH© 2023 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.AAMP Global is not affiliated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC. The termsOEM, Jeep®, Wrangler®, and Gladiator® all terms are used strictly for identification purposes only. It is notimplied that any part listed is a product of, or approved by, Fiat Chrysler Automobiles.Pacific Accessory CorporationPage 1Rev: v5Date:071423Introduction and FeaturesThe SRK-JW18EH is a complete radio replacement kit with integrated climate control retention for select Jeep WranglerJL and Jeep Gladiator JT vehicles. All modules and cables are included to retain important features of the factorysystem, including: steering wheel-mounted radio controls, factory reverse camera, USB ports, and AM/FM reception.Data integration with the vehicle and the Stinger HEIGH10™ radio (sold separately) allows for the retention and additionof the following features: vehicle performance gauges and information, climate controls, vehicle settings, factoryamplifier control, and forced camera activation. Simplified installation and setup menus allow direct programmingof camera triggers, steering wheel controls, and other settings of the radio and CH4A-JW18 interface. See ImportantNotes (next section) for additional information.Plug & Play wiring harnesses and cables allow for quick and easy installation without the need to cut or splice anywiring.Important Notes1. Does Not Retain:Cluster Display Features• Compass (when equipped with 7” or 8.4” screen)• Clock• Phone pop-ups• Navigation pop-upsFactory Amplifier Features• Speed Controlled VolumeUconnect Features• Uconnect Access Remote Start / Lock / Unlock• SOS / Assist• Vehicle Location Service• WiFi-HotspotSiriusXM Guardian Services• SiriusXM RadioWe recommend reading this manual thoroughly to familiarize yourself with the entire processprior to beginning the installation.Tools needed for installation: 7mm socket, 10mm socket, ratchet,ratchet extension, T20 torx screwdriver, T25 torx screwdriver,pick tool or small flathead screwdriver, plastic panel removal tool(example - PAC part number TL-PRY2).1. HEIGH10™ Display Mounting Panel (SE-JW18H)2. Main Bracket, Panel Clips and Mounting Screws3. Radio Module Mounting Brackets (L&R)4. Chime Speaker (P-RPA-SPK)5. Main Wiring Harness (RPK-JW18-HAR)6. Radio Replacement Interface Module (CH4A-JW18)7. HD Camera Retention Module (RPA-HD1)8. PAC-LINK Interface Module (PL1)9. 7’ USB Port Retention Adapter (USB-UN2)10. 18” Factory Camera Extension Harness (FAK-EXT-1)11. 18” HDMI Cable (HDMI-18-2M)12. 8” USB Hub Retention Adapter (USB-UN1)13. 18” Data Harness (10P-2-10P-18)14. AM / FM Antenna Adapter (BAA22)15. Satellite Antenna Adapter (SAT-01)16. CAN-Bus Connection Harness (MQS4PT-36)17. 6” Data Harness (10P-2-10P-6)18. HD Camera Mounting BracketTools Needed; Included Components1461415161017852113137189122. When connected properly, the USB port inside the center console will function for Apple Carplay/Android Auto, and allother USB ports will be used for USB thumb drives and charging only.3. Ensure that the CH4A-JW18, PL1, and RPA-HD1 modules have been updated to the latest version of firmwarebefore installing into the vehicle. Refer to the Updating Firmware section at the end of the manual for firmware updateinstructions.4. When connecting an HDMI streaming device to the RPA-HD1, use an HDMI extension cable to position it away from themodule to ensure proper functionality. We recommend placing the HDMI device in the glove box. Failure to follow thedirections may result in module malfunction.