Panasonic BB-HCM381A Getting Started

Also see for BB-HCM381A - Network Camera: Operating instructions Operating instructions Important information Installation guide Troubleshooting

Contents

Panasonic BB-HCM381A Getting Started Manual pdf 4 page image

3. Setting up Internet Access to the Camera.By registering with the Viewnetcam.com FREE DynamicDNS service,you can create a personalized web address at which your camera's livevideo can always be found on the Internet. For detailed information,access "http://www.viewnetcam.com".Click [Automatic Setup (Internet Access)].Sets up the camera to view on the LAN.Sets up the Internet access to thecamera.Manually sets up the camera.Disables IPsec. If disabled, the button isdisplayed gray.Displays the Setup page(see page 45 of the OperatingInstructions on the CD-ROM).The Enter Network Password window is displayed. Enter theuser name and password that were set, and click [OK].When using a router that supports UPnPô, check [Enable].When using a router that does not support UPnPô, check[Disable]. Then click [Next>].ï Check if your router supports UPnPô referring to the router'smanual. If UPnPô is not supported, the router has to be manuallyconfigured for port forwarding. Refer to the router's manual forinstruction on how to do it.ï If you select [Disable], skip to step .To register with the "Viewnetcam.com FREE DynamicDNSservice", check [Register with Viewnetcam.com] and click[Next>].ï If you selected [Do not register with Viewnetcam.com], skip to step .The Enter Network Password window is displayed. Enterthe user name and password that were set, and click [OK].The "Viewnetcam.com FREE DynamicDNS service"website is displayed. Follow the displayed instructions forregistration.ï If the message "Failed to configure the router's Port Forwarding by UPnP" isdisplayed, your router may not support UPnP ô or UPnPô is not enabled.Enable your router's UPnP ô or set Port Forwarding manually following therouter's manual, and try Automatic Setup again. For more information aboutsetting up a router, refer to the Panasonic Network Camera support website athttp://panasonic.co.jp/pcc/products/en/netwkcam/ï If the message "Failed to register with Viewnetcam.com." is displayed, con-firm that the router is connected to the Internet.When "Setup completed" is displayed, make a note of theURL and click [To Single Camera page].ï When [Enable] was selected at step.ï When [Disable] was selected at step.Noteï The port number must be specified at the end of the camera URL.For exampleUsing port 80:http://(Cameraname).viewnetcam.com or http://IP AddressUsing any other port:http://(Cameraname).viewnetcam.com:Port Number orhttp://IP Address:Port Numberï Make a note of the URL for the camera.ï The URL for the local network access may be different from the one set up onthe previous page. Make a note of the URL here again.When the Single Camera page is displayed, the setup iscomplete.Noteï If the camera cannot be accessed,see page 9 of the Troubleshootingon the CD-ROM.ï To ensure that the most currentimage is displayed, Internet Explorershould be configured as follows.This will not have a negative effecton normal use.1. While viewing any website, click[Tools] → [Internet Options].2. In the section "Temporary InternetFiles", click [Settings] and check[Every visit to the page].Registration with the "Viewnetcam.com FREEDynamicDNS service"Security Warning window on Microsoft Windows XP Service Pack 2To view a video (Motion JPEG) or to use audio feature, ActiveX Controls must be installed.Follow the steps below to install ActiveX Controls.Click the warning displayed above the tabs, and click [InstallActiveX Control...]. Click [Install].********4

/ 4

Related manuals for Panasonic BB-HCM381A - Network Camera