Panasonic BT-LH2600W Operating Instructions Manual

Also see for BT-LH2600WE: Mechanical Parts List

Panasonic BT-LH2600W Operating Instructions Manual Manual pdf 19 page image

19The underlined values are factory preset setting values.*1 During 2 screen display, the changes are not reflected in the still image of the main window.*2 When “RGB-COMP.” is selected in “YPBP R/RGB” in the “INPUT SELECT” menu (J page 27), this does not operate.*3 The following sharpness values can each be set,1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)2) any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)3) any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)and the setting values for the selected input signal from within this group is displayed. The adjustment status isdisplayed in the bottom right when selected.*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (J page 20).*5 When selecting USER0–631) Push [ENTER] (USER changes to blue). 2) Select 0–63 with [ , ], and push [ENTER].*6 When using “SUB WINDOW” function (J page 24),1) change the setting after releasing “SUB WINDOW” function .2) we recommand “MODE2” for the image with a fast movement.*7 During Anamo size display, “SCAN ” change is not reflected.VIDEO CONFIGSub menu Settings ExplanationGAMMASELECT*1*2 Used to select the gamma curve.Standard mode FILM modeColor emphasis mode (in the gamma characteristic inwhich shades are valued more than the contrasts, it is suitable foruse by the studio and the post production, etc. )When FILM is selected, mark is displayed in the top left of the screen.FILM GAMMA*2 Used to select the type of FILM gamma mode. VARICAM use When using other types than VARICAMCOLOR TEMP. *5Used to select the color temperature. Adjustable settings 0–63 (color temperature around 3000K–9300K) Color temperature around 9300K Color temperature around 6500K Color temperature around 5600K WB adjustment mode *4 WB adjustment mode*4 WB adjustment mode *4SHARPNESSMODE*2 *3Used to select the width of the sharpness edge. Thin edge Thick edgeSHARPNESS H*2 <0–30> *3 Used to set the sharpness in the horizontal direction.When adjusting, the item display moves to the lower part of the screen.SHARPNESS V*2 <0–30> *3 Used to set the sharpness in the vertical direction.When adjusting, the item display moves to the lower part of the screen.I-P MODE*2*6 Used to set the mode for IP change. Within Field Normal modeMONO*2 Used to switch between color and monochrome (MONO). Color Monochrome* When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.ANAMO*2*7 If an Anamo lens has been used on the camera, and input throughSDI 720/60P, 59.94P, the picture is resized to Anamo sizemagnification. (a vertically compressed signal can be amplifiedvertically and corrected when it is displayed.)SD ASPECT*2 <4:3><16:9>Used for setting the aspect ratio settings when using SD signal input.<4:3> 4:3 display <16:9> 16:9 displaySCAN*2 Used to set under-scan and normal display.Normal display Under-scanNOISE WIPE*2 This makes a fluid and smooth contrast obtainable.This is especially effective for continuously changing the contrast ofthe source signal or CG signal when the S/N is very high. Noise reduction mode. Depending on the camera, this mode canbe especially effective for dark scenes. We recommend leavingthis setting “ON” under normal conditions.Main Menu (continued)