Panasonic CF-25 Operation Instructions Manual

Also see for CF-25: Operating instructions Operating instructions Operating instructions Operating instructions

3This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, includinginterference that may cause undesired operation.W a r n i n gTo assure continued compliance, use only shielded interfacecables when connecting to a computer or peripheral. Also, anychanges or modifications not expressly approved by the partyresponsible for compliance could void the user's authority tooperate this equipment.F e d e r a l C o m m u n i c a t i o n s C o m m i s s i o n R a d i oFrequency Interference StatementFor U.S.A.Note: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordancewith the instructions may cause harmful interference to radiocommunications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or moreof the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.Consult the Panasonic Service Center or an experienced ra-dio/TV technician for help.If the plug contains a removable fuse cover you must ensure thatit is refitted when the fuse is replaced.If you lose the fuse cover the plug must not be used until a re-placement cover is obtained.A replacement fuse cover can be purchased from your localPanasonic Dealer.IF THE FITTED MOULDED PLUG IS UNSUITABLE FORTHE SOCKET OUTLET IN YOUR HOME THEN THE FUSESHOULD BE REMOVED AND THE PLUG CUT OFF ANDDISPOSED OF SAFELY.THERE IS A DANGER OF SEVERE ELECTRICAL SHOCKIF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPSOCKET.Check for the ASTA mark or the BSI mark on the bodyof the fuse.This appliance is supplied with a moulded three pin mains plugfor your safety and convenience.A 3 amp fuse is fitted in this plug.Should the fuse need to be replaced please ensure that the re-placement fuse has a rating of 3 amps and that it is approved byASTA or BSI to BS 1362.FOR YOUR SAFETY PLEASE READ THE FOLLOWINGTEXT CAREFULLYFor U.K.W a r n i n g sThis equipment is not designed for connection to an IT powersystem.(An IT system is a system having no direct connections be-tween live parts and Earth; the exposed-conducive-parts of theelectrical installation are earthed.An IT system is not permitted where the computer is directlyconnected to public supply systems in the U.K.)Disconnect the mains plug from the supply socket when thecomputer is not in use.This equipment is produced to BS800/1983.Blue: NeutralBrown: LiveI m p o r t a n tThe wires in this mains lead are coloured in accordance with thefollowing code:As the colours of the wires in the mains lead of this apparatusmay not correspond with the coloured markings identifying theterminals in your plug, proceed as follows:The wire which is coloured Blue must be connected to the ter-minal which is marked with the letter N or coloured BLACK.The wire which is coloured Brown must be connected to theterminal which is marked with the letter L or coloured RED.How to replace the fuseOpen the fuse compartment with ascrewdriver and replace the fuse.If a new plug is to be fitted please observe the wiring code asshown below.If in any doubt please consult a qualified electrician.Under no circumstances should either of these wires be con-nected to the earth terminal of the three pin plug, marked withthe letter E or the Earth Symbol .The mains plug on this equipment must be used to disconnectthe mains power.Please ensure that a socket outlet is available near the equipmentand shall be easily accessible.