26TroubleshootingTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contactPanasonic Technical Support (è pages 37 - 41). You can also check the computer’s status in the PC Information Viewer (èReference Manual “Troubleshooting (Advanced)”). Starting UpCannot start up.The power indicator or bat-tery indicator is not lit.l Connect the AC adaptor.l Insert a fully charged battery.l Remove the battery pack and the AC adaptor, then connect them again.l Even if the AC adaptor and battery pack are correctly connected, if the battery indicatoris not lit, the AC adaptor protection function may be operating. Disconnect the AC cord,wait three minutes or more, and reconnect the AC cord.l If a device is connected to the USB port, disconnect the device, or set [USB Port] or[Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility.l If a device is connected to the ExpressCard slot, disconnect the device, or set[ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility.l Press Fn + F8 to turn off the concealed mode.l Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot] should be set to[Enabled] / [Disabled].The power is turned on but“Warming up the system (upto 30 minutes)” appears.l The computer is warming up before start up. Wait for the computer to start up (takesup to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failedto warm up and does not start. In this case, turn off the computer, leave it in an envi-ronment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on thepower once more.Cannot turn on the computer.The computer does not re-sume from sleep.(The power indicator blinksquickly in green.)l Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, thenturn on the power again.After adding or changingthe RAM module, the poweris turned on but nothing isdisplayed on the screen.l Turn off the computer and remove the RAM module, then confirm whether the RAMmodule has compliant to specification. When the RAM module has conformed to specifi-cation, install it again.The computer does notenter sleep mode while thescreen saver is running. (Thescreen stays black.)l Press and hold the power switch for 4 seconds or longer to shut down the computerforcibly. (Data not saved will be lost.) Then disable the screen saver.It takes time for the powerindicator to light up.l If the power switch is pressed immediately after the battery pack has been mounted onthe computer, and while the AC adaptor is not connected, it may take about five secondsbefore the power indicator lights up and the computer turns on. This is because thecomputer is checking the remaining battery charge; it is not a malfunction.You have forgotten the pass-word.l Supervisor Password or User Password: Contact Panasonic Technical Support(è pages 37 - 41).l Administrator password: If you have a password reset disk, you can reset the administrator password. Set thedisk and enter any wrong password, then follow the on-screen instructions and set anew password. If you do not have a password reset disk, reinstall (è page 22) and set up Windows,and then set a new password.“Remove disks or othermedia. Press any key torestart” or a similar messageappears.l A floppy disk is in the drive (optional) and it does not contain system startup information.Remove the floppy disk and press any key.l If a device is connected to the USB port, disconnect the device, or set [USB Port] or[Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.l If a device is connected to the ExpressCard slot, disconnect the device, or set[ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility.l If the problem persists after removing the disk, it may be a hard disk failure. ContactPanasonic Technical Support (è pages 37 - 41).l Set [UEFI Boot] to [Disabled] in the [Boot] menu of the Setup Utility.