IC600 : C2CBKYY000239PinNo.Port Description I/O (V)1 NC Remote control signal input I 02 VOL.LVL(NC)No Connection - -3 NC No Connection - -4 NC No Connection - -5 NC No Connection - -6 BYTE - I 07 CNVSS - I 08 NC No Connection - -9 NC No Connection - -10 /RESET System reset H:RESET OFF I 3.211 XOUT Main clock output O 2.712 VSS Ground I 013 XIN Main clock input I 2.014 VCC1 Power Supply I 3.315 /NMI - I 3.316 ACC.DET Power Supply ACC Detection HFACC ONI 3.417 BAT.DET Power Supply +B Detection H:BATT ONI 3.418 RMC IN Remote control signal state input I 019 IE. BUS. IN - I 3.420 ILRST Abnormal reset flag to Nabismicrocomputer L: NormalO 021 ACC.DET.OUTACC ON fixation signal to Nabismicrocomputer H: ACC ONO 3.322 NC No Connection - -23 SYS.LATCH Data fixation signal output to systempower supply ICO 3.324 SYS.DATA Data signaling output to systempower supply ICO 3.325 SYS.CLK Clock pulse output to system powersupply ICO 3.326 BEEP BEEP Output O 027 IE. BUS.IN IE Bus Input I 3.428 IE. BUS.OUT IE Bus Output O 029 DVD.TX DVD4.5U start-stop data signalingoutputO 030 DVD.RX DVD4.5U start-stop data signalinginputO 031 SYS.STBY System power supply start control O 3.332 SYS.STBY2 System power supply internalregulator change signal H: External5VO 3.333 NAVI.RX Data output for Nabismicrocomputer communicationO 3.434 NAVI.TX Data input for Nabis microcomputercommunicationI 3.435 NC No Connection - -36 /DVD.RESET(NC)No Connection - -37 WDT.ON Customer engineer control withbuilt-in RESET IC WDT H: WDT ONO 3.338 WDT.CLK Release signal with built-in RESETIC WDTO 3.339 /ILL.DET Vehicle ILL-SW detection H: ILL-SW I 3.340 NC No Connection - -41 NC No Connection - -42 NC No Connection - -43 LED.CNT2(NC)No Connection - -44 LED.CNT1 Insertion entrance LED controlsignal output 1 H:LED ONO 3.345 EVOL2 Speech output attenuator control 2 O 0PinNo.Port Description I/O (V)46 EVOL1 Speech output attenuator control 1 O 047 ATTP0 (NC) No Connection - -48 NAVI MUTE External monitor speech outputcontrol H:MUTE ONO 049 STBY (NC) No Connection - -50 DAC.MUTE Nabis voice guide MUTE controlH:MUTE ONO 3.251 S.MUTE.CANSEL (NC)No Connection - -52 NMUTE MUTE to power amplifier H: MUTEONO 3.353 /AUDIO.RST Reset signal of RESET IC H:RESET OFFO 3.354 AUDIO.NMI Soft NM I-signal to RESET IC H:ACC ONO 3.355 ACC.ON AC C power supply ON fixationsignal H: When set operatesO 3.356 ADPG Set distinction since 1S/2S H: since2SI 057 TEST Test mode signal detection H: TESTsignal OFFI 3.358 PKB Parking brake signal detection H:Brake ONI 3.359 TMC.RST Reset output port for external RDSTMC equipment L: RESETO 060 CVCC2 Power-supply voltage I 3.361 NAVI DISP NAVI display notification outputsignalO 3.362 VSS Ground I 063 NC No Connection - -64 NC No Connection - -65 NC No Connection - -66 NC No Connection - -67 NC No Connection - -68 NC No Connection - -69 NC Input for ACC voltage detection I 1.570 THM Input for ambient temperaturedetection with thermistorI 1.471 VD.DOWN Chroma IC: For 12C-BUStransmission timing detectionI 3.372 /DVD.MUTE DVD MUTE trigger input I 3.473 OPEN.KEY Lid OPEN state detection H: OPEN I 074 NC No Connection - -75 NC No Connection - -76 SPD CNT - - -77 MAX (NC) No Connection - -78 NC No Connection - -79 NC No Connection - -80 NC No Connection - -81 ACONT2(NC)No Connection - -82 ACONT1(NC)No Connection - -83 RGB.MUTE(NC)No Connection - -84 NC No Connection - -85 VCONT2(NC)No Connection - -86 VCONT1(NC)No Connection - -87 NC No Connection - -88 NC No Connection - -89 NC No Connection - -90 NC No Connection - -9 TERMINALS DESCRIPTION9.1. Main Block5CN-D105T