Panasonic CQ-C1120U Operating Instructions Manual

Also see for CQC1100U - AUTO RADIO/CD DECK: Operating instructions

Contents

Panasonic CQ-C1120U Operating Instructions Manual Manual pdf 15 page image

❐ Preparation• Disconnect the cable from the negative batteryterminal (see warning and caution below).• Remove Mounting Collar q and Trim Plate u from themain unit temporarily, which are already mounted atshipment.*• Unit should be installed in a horizontal position with thefront end up at a convenient angle, but not more than 30°.❐ Dashboard InstallationInstallation OpeningThis unit can be installed in any dashboard havingan opening as shown below. The dashboard shouldbe 3 ⁄ 16" (4.75 mm)–7 ⁄ 32" (5.56 mm) thick inorder to be able to support the unit.17ENGLISH18ENGLISH2928 CQ-C1200U/C1120U/C1110U/C1100U CQ-C1200U/C1120U/C1110U/C1100UCautions:¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure yourhands and fingers.1234Mounting Holest Mounting BoltInsert Trim Plate u.After installation reconnect the negative(–) battery terminal.First complete the electrical connections, andthen check them for correctness.(a page 30)The included Mounting Collar q isdesigned specially for this unit. Donot use it to attach any other model.Mounting Springs (C)y Power ConnectorEngage the MountingSprings (C) in themounting holes of theMounting Collar qfirmly.Mounting SpringMountingHoleInsert Mounting Collar q into the dash-board, and bend the mounting tabs outwith a screwdriver.The tabs to be bent vary depending onthe car. To securely install the unit, fullybend a number of the tabs so that thereis no rattling.Example: Tabq MountingCollar(a) Using the rear support strap er Tapping screw(5 mmø×16 mm)w Hex. nut(5 mmø)e Rear support strapt Mounting bolt (5 mmø)q Mounting collarFire wall of car3 mmø(b) Using the rubber cushion (option)t Mounting bolt(5 mmø)q Mounting collarRear support bracket(provided on the car)Rubber cushion (option)Establish the rear connection of the unit.After fixing Mounting Bolt t and Power Connectory, fix the rear of the unit to the car body by eithermethod (a) or (b) shown the previous page.Installation (Continued)❐ Installation Hardwarei Dismounting Plate(YFX214C323ZA)12Less than 30 °Caution: Various settings that have been stored in thememory in other on-board equipment (car navigationetc.) may be lost if the battery terminals are discon-nected.Therefore, we recommend to make a record of or toback up the settings before disconnecting the termi-nals.After completing installation of the main unit, set theequipment again according to the record.Warning: If your car is equipped with air bagand/or anti-theft systems, specific proceduresmay be required for connection and disconnec-tion of the battery to install this product.Before attempting installation of this electroniccomponent, contact your car dealer or manufac-turer to determine the required procedure andstrictly follow their instructions.FAILURE TO FOLLOW THE PROCEDURE MAYRESULT IN THE UNINTENDED DEPLOYMENT OFAIR BAGS OR ACTIVATION OF THE ANTI-THEFTSYSTEM RESULTING IN DAMAGE TO THE VEHI-CLE AND PERSONAL INJURY.ItemNo. Diagram Q’tytyuMounting Collar*(FX0214C316ZA)Hex. nut (5 mmø)(YJN994C002ZA)Rear support strap(YFG044C002ZA)Tapping screw (5 mmø×16 mm)(XTT5+16AFK)Mounting Bolt (5 mmø)(YEJV014C002A)Power Connector(YEAJ02877)Trim Plate*(YFC054C063ZA)111111qwer(182 mm)(53 mm)7 5/ 32"2 3/32"

/ 17

Related manuals for Panasonic CQC1100U - AUTO RADIO/CD DECK