Panasonic CQ-C1301NW Operating Instructions Manual

Also see for CQ-C1301NW: Operating instructions Operating instructions

Contents

GeneralCQ-C1321NMUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AFPUSHSELTUNE/TRACKFOLDERBAND1 2 3 4 5 6PWR PTYVOLSRC DISPAPMD·MD·MSRCGeneral OperationsPower On/OffSet your car's ignition switch to the ACC or ON position.Power on: Press [SRC] (PWR).Power off: Hold down [SRC] (PWR) formore than 1 second.Source SelectionPress [SRC] to change the source.Volume Adjustment(Setting Range: 0 to 40, Default: 18)Turn [VOL].MuteON: Press [MUTE]. ( lights.)OFF: Press [MUTE] again.SQ (Sound Quality)SQ is a function that can call up various sound types at thetouch of button in accordance with your listening musictype.1 Holding down [SQ] for more than 1 sec-ond activates the SQ selection mode.2 Press [SQ] to select the sound type (SQ)as follows:Notes:¡ If no operation takes place for more than 5 seconds inthe SQ selection mode, the display returns to the regularmode.¡ Settings of SQ, bass and treble are influenced one anoth-er. If such an influence causes distortion to the audiosignal, readjust bass/treble or volume.[MUTE]toggles mute on/off.(SQ) (Sound Quality)selects a sound type (SQ). (Hold it down formore than 1 second.)Remote control sensorfor an optional remote control unit (CA-RC61EX).[VOL] (Volume)[SRC] (Source)selects a source.(PWR) (Power)toggles power on/off.Radio Disc Player (FLAT) flat frequency response:does not emphasize any part. (Default)(ROCK) speedy and heavy sound:exaggerates bass and treble.(POP) wide-ranged and deep sound:slightly emphasizes bass and treble.(VOCAL) clear sound:emphasizes middle tone and slightly empha-sizes treble.TroubleshootingTrouble Check pointNo power● Start the engine. (Or turn the ignitionswitch to the ACC position.)● Verify the wiring. (battery lead, powerlead, ground lead, etc.)● Fuse blown (Contact the nearestPanasonic Service Centre.)● Ask a professional for fuse replacement.● Be sure to use the same rated fuse.No sound● Disable the mute function.● Verify the wiring.● Wait until the dew disappears beforeturning on the unit.Noise ● Make sure that grounding is establishedproperly.CommonFrequentnoise● Tune in to another station of high-inten-sity waves.● Make sure that the antenna mountedpoint is grounded properly.RadioPreset datadeleted● The preset memory is cleared to returnto the original factory setting when thepower connector or battery is discon-nected.No sound, or discis automaticallyejected● Load the disc correctly.● Clean the disc.Disc PlayerSound skip,poor soundquality● Clean the disc.Sound skipdue tovibration● The maximum permissible tilt angle is30°.● Secure the unit.Disc notejectable● Press [u]. If the disc is still not ejected,contact the nearest Panasonic ServiceCentre.No sound fromleft, right, front,or rear speaker● Adjust the balance and fader.● Verify the wiring.Trouble Check pointLeft and rightsounds arereversed● Connect the speaker lead correctly.Error Display Messages(The disc is ejected automatically.)The disc is dirty, or is upside down.● Check the disc.(The disc is ejected automatically.)The disc has scratches.● Check the disc.No operation by some cause.● If normal operation is not restored, con-sult your dealer or the nearest ServiceCentre to ask for repairs.Cannot read the file● Check the file.A WMA file can be copyrighted.● The file protected by copyright is notplayable.If You Suspect Something WrongCheck and take steps as described below.If the described suggestions do not solve the problem, it is recom-mended to take the unit to your nearest authorized Panasonic ServiceCentre. The product should be serviced only by qualified personnel.Please refer the checking and the repair to professionals. Panasonicshall not be liable for any accidents arising out of neglect of checkingthe unit or your own repair after your checking.Warning¡ Do not use the unit in an irregular condition, for example, with-out sound, or with smoke or a foul smell, which can causeignition or electric shock. Immediately stop using the unit andconsult your dealer.¡ Never try to repair the unit by yourself because it is dangerousto do so.Radio (AM [LW/MW]/FM)CQ-C1321NMUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AFPUSHSELTUNE/TRACKFOLDERBAND1 2 3 4 5 6PWR PTYVOLSRC DISPAPMD·MD·MBAND1 2 3 4 5 6SRC DISP[TUNE ]] [TUNE []down/up the frequency. (Hold it down formore than 0.5 seconds and release it for seektuning.)[BAND]selects a band in the radio source.(APM) (Auto Preset Memory)executes APM in the radio source. (Hold itdown for more than 2 seconds.)[DISP] (Display)switches the information onthe display.[SRC] (Source)selects a source.[1] to [6]selects a preset station in the radio source,and presets the current station. (Hold it downfor more than 2 seconds.)Station Preset Radio Source DisplayOperation Flow1 Press [SRC] to select the radio source.2 Press [BAND] to select a band.3 Select a station.Frequency adjustment[TUNE ]]: Lower[TUNE []: HigherNote: Hold down either of them for more than 0.5 sec-onds and release it for seek tuning.Preset station selectionPress the corresponding preset button from [1] to [6] totune into a preset station.Useful functions such as AF, TA, PTY are available in the RDS (Radio Data System)-ready areas.Some FM stations are broadcasting added data compatiblewith RDS. This radio set offers convenient functions usingsuch data.RDS service availability varies with areas. Please understand ifRDS service is not available in your area, the following serviceis not available, either.The following functions are available when receiving RDSstations.AF (Alternative Frequency)The following functions are available when the AF mode isactive ( lights).¡ When receiving conditions become bad, a station with bet-ter receiving conditions is automatically tuned in to.¡ When executing APM, only RDS stations are selected.¡ When calling up a preset station, a best receiving station isselected automatically. (BSR Best Stations Research)Notes:¡ The AF sensitivity can be adjusted.¡ The AF available range can be adjusted. (a “FunctionSettings”)TA (Traffic Announcement)The following functions are available when the TA mode is active( lights).¡ A TP station is automatically searched for and received atthe instant of toggling the TA mode on if you are receivinga non-TP station or TP station with poor reception.¡ When executing station search or APM, only TP stationsare selected.¡ Setting to TA on with the unit in another mode, it will auto-matically switch to radio mode and output the trafficannouncement when the traffic announcement begins. Thetraffic announcement having finished, the unit will return tothe previous mode. (TA Standby Mode)PTY (Programme Type)The following functions are available when the PTY mode isactive.¡ The PTY of receiving station appears.¡ Programs can be searched for by PTY.Note: PTY language can be selected. (a “Function Settings”)Other functions of RDSCT (Clock Time)The clock is automatically adjusted.PS (Programme Service Name)As well as the frequency, the name of the broadcast stationappears.EON (Enhanced Other Network)RDS information is updated constantly in response to thecurrent position.EON-TATraffic information from the current and other networkstations can be received.Emergency Announcement ReceptionEmergency announcement automatically appears on thedisplay when it is received.AF LevelHold down [TA] (AF) for more than 2 seconds to select AFlevel.Low level AF operating sensitivity. (Default)High level AF operating sensitivity.When the AF network of an RDS station is notrequired.PI Seek (Programme Identification Seek)If reception becomes poor when tuning in a preset station,press the same preset number button. The same station withbetter reception will be searched for.Press same preset number button again to cancel.Note: For PI Seek, cancel the TA mode first, then execute PISeek.AF (Alternative Frequency)PTY (Programme Type)What is RDS?TA (TrafficAnnouncement)Radio Data System (RDS) in FM Broadcasting