Panasonic CQ-DF402U Operating Instructions Manual

Also see for CQDF402U - AUTO RADIO/CD DECK: Operating instructions Operating instructions Service manual Operating instructions

Contents

Panasonic CQ-DF402U Operating Instructions Manual Manual pdf 12 page image

ENGLISH16CQ-DF402/DFX302U 25ENGLISH15CQ-DF402/DFX302U24Electrical ConnectionsAnti-Theft SystemDisplay Security indicatorBlinksOFFSecurity IndicatorThe security indicator blinks when the removableface plate is removed from the unit.Press and hold [SEL] to turn the security indicatoron or off. (“LED ON” or “LED OFF”).Install Removable Face Plate1 Fit the face plate with its right or left hole onone of the pins provided on the main unit.2 Fit the other hold on the other pin applyingslight pressure.3 Move the face plate up and down a few times tomake sure it is secure. Then close the frontpanel and press down the right side of the faceplate until it clicks into plate.Cautions:≥ This face plate is not water-proof. Do not expose it to water or excessive moisture.≥ Do not remove the face plate while driving your car.≥ Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.≥ Do not touch the contacts on the face plate or on the main unit, since this may result in poor electricalcontacts.≥ If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.≥ Do not apply a strong downward force onto the face plate and do not put anything on it while it is open, orit might be damaged.This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.The security indicator will blink.Place the Removable FacePlate into Case1 Switch off the power of the unit.2 Remove the removable face plate. (➡ page 23)3 Gently press the button of the case and openthe cover. Place the face plate into the case andtake it with you when you leave the car.12 37 Removable face plate caseSecurity indicatorContactDefault❐ Wiring Diagram Only for CQ-DFX302UNo. Item Q’ty6 Power connector 1Recommended external amplifier combination (example)≥ Pre-amp out (rear/front) [CY-M9054 (4 channels system)]≥ Subwoofer out [CY-M9054 (2 channels system) or CY-M7052 (1 channel system)]WhiteRed(MONO)Power connectorAntenna6YellowBATTERY 15A Battery leadTo the car battery,continuous +12 V DCFuse (15 A)Red Resistor (1 k≠)ACC Power leadTo ACC power,+12 V DCDark blueMotor antenna relay control lead(To motor antenna) (Max. 500 mA)This lead is not intended for use with switchactuated power antenna.BlackGround leadTo a clean, bare metallicpart of car chassis.(r)(s)(r)(s)(r)(s) (r)(s)Left speaker(Front)Right speaker(Front)White Gray Green VioletWhite/black stripe Green/blackstripeViolet/black stripeGray/black stripeFRONT SP REAR SPLeft speaker(Rear)Right speaker(Rear)S• W-OUTSpeaker leadSubwoofer cordCQ-DFX302UPre-Amp output connector (Front)Pre-Amp output connector (Rear)L (White)R (Red)Amp. relay control power leadThis lead is for connection to the power amplifier.Cautions:≥ This product is designed to operate of a 12 V DC, negative ground battery system.≥ To prevent damage to the unit, be sure to follow the wiring diagram below.≥ Remove approx. 1⁄4z (5 mm) of protective covering from the ends of the leads before connecting.≥ Do not insert the power connector into the unit until the wiring is completed.≥ Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cablesand keep cable terminals free from touching any metal parts.≥ Remember, if your car has a drive computer or a navigation computer, the data of its memory may beerased when the battery terminals are disconnected.Accessory used for wiring