Panasonic CQ-VD7001W Operating Instructions Manual

Contents

Panasonic CQ-VD7001W Operating Instructions Manual Manual pdf 32 page image

VIDEO-OUTVTR-INPRE-OUT REARREMOTE-OUTS.W-OUTPRE-OUT CENTERTV-CONTPRE-OUT FRONTCAMERA-INCH/AUX-INREMOTE-IN65CQ-VD7001WNote:¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer oryour dealer if other methods are required.Video Output Terminal (VIDEO-OUT)Connect the rear monitor. (a page 68)Radio Antenna Connector (RADIO ANT IN)DIN ConnectorTo the DIN connector of a CD changer/DVD Changer.(e.g. CX-DP880, CX-DH801W).RGB ConnectorTo the Panasonic Car Navigation System (available in future).Remote-Out LeadTo Remote-In of connected device.Pre-Out Connector (front)To external amplifier.Pre-Out Connector (center)To external amplifier.Pre-Out Connector (rear)To external amplifier.Pre-Out Subwoofer connector (mono)To external amplifier.Video Input Terminal (VTR-IN)Connect a VCR, camcorder, other brand’s carnavigation system, etc. (a page 68)Remote-In Lead(not used)Changer/AUX Input ConnectorTo the RCA cord of a changer/AUX.Camera Input Terminal (CAMERA-IN)Connect a rear view camera. (a page 69)/DVD Changer (a page 67)TV Control Lead (TV-CONT)(not used)(R)(Red)(L)(White)(R)(Red)(L)(White)(R)(Red)(L)(White)(Yellow)(R)(Red)(L)(White)(R)(Red)(L)(White)(Yellow)(Yellow)(Blue/red stripe)(Brown/black stripe)(Black)(Black)(Black)CQ-VD7001W(Rear)This manual refers to the connection to the Panasonic car navigation system that may possibly come on the market inthe future. Descriptions regarding the connection with Panasonic car navigation system are boxed with dotted line.64 CQ-VD7001WElectrical ConnectionsBATTERY 15 AREVERSESIDE BRAKENAVI MUTEANT-CONT MAX 0.1AFRONT SPREAR SPAMP-CONT MAX 0.1AACCMotor Antenna Relay Control Lead (Blue)(To motor antenna) (Max. 100 mA)This lead is not intended for use with a switch actuatedpower antenna.Front Right + (Gray)Front Right – (Gray/black stripe)Front Left + (White)Front Left – (White/black stripe)Rear Right + (Violet)Rear Right – (Violet/black stripe)Rear Left + (Green)Rear Left – (Green/black stripe)External Amplifier Control Power Lead (Blue/white stripe)To an external amplifier.Battery Lead (Yellow)To the car battery, continuous +12 V DC.Power Lead (Red)To ACC power, +12 V DC.Ground Lead (Black)To a clean, bare metallic part of the car chassisSpeaker connections• Do not connect more than one speaker to one set ofspeaker leads (except for connecting to a tweeter).• Do not use a 3-wire type speaker system having a com-mon earth lead.Navi Mute Lead (Orange)Connect to the Navi Mute Lead of the Panasonic carnavigation system. (available in future)Side Brake (Parking Brake) Connection Lead (Blue/yellowstripe)Be sure to wire the side brake (parking brake) for safety andpreventing accidents. (a page 63)Reverse Lead (Violet/white stripe)When connecting the rear view camera, use the reverse lead.(a page 69)Note: Use a Reverse Extension Cord !4 if needed.(Noise Filter)(Fuse 15 A)(Resistor 1 kΩ)Caution¡This unit is designed for use in a car having a 12 V negative ground battery system.¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from anymetal parts.¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery mayclear the memory.¡Run the cords avoiding the spots where the temperature can be extremely high.!3 Power Connector

/ 35

Related manuals for Panasonic CQ-VD7001W