Panasonic CY-111 Series Instructions Manual

Panasonic CY-111 Series Instructions Manual Manual pdf 1 page image

INSTRUCTIONSCylindrical Photoelectric SensorCY-111, CY-19q, CY-12q SeriesThank you for purchasing products from Panasonic. Please read thisInstruction Manual carefully and thoroughly for the correct and optimumuse of this product. Kindly keep this manual in a convenient place for quickreference.WARNING● Never use this product as a sensing device for personnel protection.● In case of using sensing devices for personnel protection, use prod-ucts which meet laws and standards, such as OSHA, ANSI or IECetc., for personnel protection applicable in each region or country.1 Cautions● This product has been developed / produced for industrial use only.● This product is suitable for indoor use only. The cable extension up toa total of 10m or less with a strength of 0.34mm2 or less (each emitterand receiver of the thru-beam type) is possible.● Make a cable length as short as possible to lessen noise pickup.● Make sure that the power supply is off while wiring.● Verify that the supply voltage including the ripple is within the rating.● If power is supplied from a commercial switching regulator, ensure thatthe frame ground (F.G.) terminal of the power supply is connected toan actual ground.● Shortcircuiting the load or wrong wiring may burn or damage theproduct.● Ensure that an isolation transformer is utilized for the DC power sup-ply. If an autotransformer is utilized, the main body or power supplymay be damaged.● If the used power supply generates a surge, connect a surge absorberto the power supply to absorb the surge.● Do not use the sensor during the initial transient time (0.5 sec) afterthe power supply is switched on.● Do not run the wires together with high-voltage lines or power linesor put them in the same raceway. This can cause malfunction due toinduction.● Avoid using the product where there are strong magnetic fields as theymay prevent the product from working according to the specification.● Take care that the sensor is not directly exposed to a fluorescent lampfrom a rapid-starter lamp or a high frequency lighting device, as it mayaffect the sensing performance.● Protect the sensor from water, oil, grease, organic solvents such asthinner, etc., strong acid, and alkaline.● Avoid using a product where there is excessive vapor, dust or cor-rosive gases, or in a place where it could be exposed directly to wateror chemicals.● This product cannot be used in an environment containing inflam-mable or explosive gases.● Never disassemble or modify the product.2 Compliance with standards and directivesThis product complies with the following standards andregulations.● For the EU: EMC Directive 2004/108/EC● For the US and Canada:ANSI/UL60947-5-2, CAN/CSA C22.2 No.14● For Korea: S1-G-1-2009, S2-W-5-2009* In case you require a UL listing mark or C-ULlisting mark, use a class 2 power supply unit.RoHS directive● This equipment complies with RoHS (CE and Chinesedirective).3 Sensor typesCable type (2m) Connector type (M12)StandardSide view4 Part description1 2 43 31 Main body2 Mounting plate3 Nut4 Cable with connector5 MountingGeneral installation hints1. Attach the sensor directly on your equipment or use one of the optionalmounting brackets to fix the sensor.2. The tightening torque should be 3Nm or less.3. If you mount a M12 connector type, you can use the optional cable withthe connector UZZ812qqD. The tightening torque for the connector partshould be 3Nm or less.Mounting with the mounting bracket MS-CY1-11. Using the holes indicated1, screw the mountingbracket to the surface.2. Feed the sensor into themounting hole 2 andaffix it with the nuts on thesensor.12Mounting with the mounting bracket MS-CY1-21. Using the holes indicated1, screw the mountingbracket to the surface.2. Feed the sensor into themounting hole 2 andadjust its direction.3. Use the upper two screws3 to secure the sensor.1321

/ 4

Related manuals for Panasonic CY-111 Series