Panasonic CZ-CSRC3 Installation Instructions Manual

Also see for CZ-CSRC3: Service manual

Contents

Panasonic CZ-CSRC3 Installation Instructions Manual Manual pdf 1 page image

CV6233317625Installation InstructionsRemote SensorModel No. CZ-CSRC3Supplied accessoriesWood screwM3.8 × 16(2)Clamper(1)Printed in ChinaH0515-085464369822020Safety PrecautionsRead before installation Read the Installation Instructions carefully to install the unitcorrectly and safely.Be sure to read the Safety Precautions in particular beforeinstallation. After the installation is complete, perform test operation to confirmthat no abnormality is present. We assume no responsibility for accidents or damages resultingfrom methods other than those described in the installationinstructions or methods without using specified parts.Malfunctions that occurred due to the unauthorised installationmethods are not covered by the product warranty. Read the installation instructions supplied with indoor units as well.WARNINGThis symbol refers to a hazard or unsafe practicewhich can result in severe personal injury or death.CAUTIONThis symbol refers to a hazard or unsafe practice which canresult in personal injury or product or property damage.WARNING• Turn off the circuit breaker of theunits before installation.• Ask your dealer or professionalsfor installation and electric work.• This remote sensor shall beinstalled in accordance withNational Wiring Regulations.• Securely connect and fix thespecified cables for wiring.• Do not allow the connection tobe exposed to the external forceof the cables.• Choose an installation locationthat sufficiently supports theweight of the remote sensor.NOTICEThe English text is the original instructions.Other languages are translation of theoriginal instructions.CAUTION Do not use at the following locations.• Location where condensation occurs• Location where flammablegases, etc. may leak• Location where corrosivegases, etc. may leak• Location with lots of water or oildroplets (including machine oil)• Location where voltagefluctuation frequently occurs• Location where there is a machineproducing electromagnetic radiation• Location where droplets oforganic solvents spread• Location where acidic oralkaline solutions or specialsprays are frequently used Do not operate with wet hands. Do not wash with water.Note: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, follow the attached installationinstructions. Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operate this equipment.MountingInstallation PrecautionsSpecifi cationsInstallation location Wiring for the remote sensor5 mm or more50 mmor more1 to 1.5 m or moreFloor Wiring diagram Type of wiringUse cables of 0.5 to 1.25 mm 2 .Use the field supplied RC wiring with at least 1 mm in thickness of insulation partincluding the sheath.Regulations on wire diameters differ from locally to locally.For field wiring rules, please refer to your LOCAL ELECTRICAL CODES beforebeginning.You must ensure that installation complies with relevant rules and regulations. Total wire length: 500 m or less(The wire length between indoor units should be 200 m or less.) Number of connectable unitsRemote controller and remote sensor: Max. 2 (including remote sensor),Indoor unit: Max. 8Attention Be careful not to connect cables to other terminals of indoor units (e.g. power source wiringterminal). Malfunction may occur. Do not bundle together with the power source wiring or store in the same metal tube. Operationerror may occur. If noise is induced to the unit power supply, attach a noise filter.R1 R2 R1 R2 R1 R21 2 1 21 2Wired RC Remote sensorIndoor unit Indoor unit Indoor unitRC wiringRemote sensor*Wiring as shown below is prohibited.12R1R2Indoor unitTerminals for RC wiringRemote sensorRC wiring (field supply)• No polarityModel No. CZ-CSRC3Dimensions (H) 120 mm × (W) 70 mm × (D) 17 mmWeight 70 gTemperature/Humidity range 0 °C to 40 °C / 20 % to 80 % (No condensation)*Indoor use only.Power Source DC16 V (supplied from indoor unit)Number of connected indoor units Up to 8 unitsInstallation when setting Main/Sub for the remote controller and the remote sensorBe sure to set the wired remote controller to [Main].The remote controller and the remote sensor can be connected to any indoor unit.Note1 2 1 2R1 R2R1 R2R1 R2R1 R2RC wiring (field supply)• No polarityIndoor unit Indoor unit Indoor unit Indoor unit1 21 2R1 R2Terminals forRC wiringRemote sensor Remote sensorWired RC (Main) Wired RC (Main)Indoor unit Using 1 indoor unit  Using more than 1 indoor unitRC wiring(field supply)• No polarityInstallationexample1 Remove the bottom case. AttentionMounting the bottom case Tighten the screws securely until the screwheads touch the bottom case.(Otherwise, loose screw heads may hit thePCB and cause malfunction when mountingthe top case.) Do not over-tighten the screws.(The bottom case may be deformed, resultingin fall of the unit.)Connecting the remote control wiring Arrange the wires as shown in the illustrationfor  in step 2, avoiding unnecessary wiresbeing stored in the case. (Caught wires maydestroy the PCB.) Avoid wires touching parts on the PCB.(Caught wires may destroy the PCB.)Flat-bladescrewdriverInsert the driverand slightly turn.2 Mount to the wall.Exposed type Embedded type132Cut here with anipper and removethe burr witha file.Mount the top case. Align the claws of thetop case and then alignthe claws of the bottomcase.Mount the bottom caseto the wall.Connect the remote control wiring. Arrange the wires along the groove ofthe case.Wood screw (supplied)ClawHole for screwWall to fix theremote sensorClaw (2 places)Top case(Back side)Remove the coating. Approx. 6 mmRemove the sheath. Approx. 150 mmMake sure the wiring connectionis in the correct direction.Clamper(supplied)Pass throughthe hole.Bottom case(Back side)Terminal boardBottom case(Back side)Remove the coating. Approx. 6 mmMake sure the wiring connectionis in the correct direction.Top case(Back side)132Avoid the wirebeing caught.Mount the top case. Align the claws of thetop case and thenalign the claws of thebottom case.Mount the bottom case tothe wall. Pass the wire through thehole in the centre of thebottom case.Connect the remote control wiring.Wood screw (supplied)Claw (2 places)ClawHole for screwENGLISH177012066.811 6.84.44.41083.533.416.61333.516.79.45.49.48(mm)Dimensions