Panasonic DMP-BD30 Operating Instructions Manual

Also see for DMP-BD30: Operating instructions Installation instructions Operation manual

27RQT9038Troubleshooting guideBefore requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chartdo not solve the problem, consult your dealer for instructions.The following do not indicate a problem with this unit:≥Regular disc rotating sounds.≥Image disturbance during search.To reset this unit PagePowerOperationDisplays(Continued on the next page)To restore the unit if it freezesdue to one of the safetydevices being activated≥Press and hold [Í/I] on the main unit for 3 seconds. (The settings remain unchanged.) —To return all settings other thansome settings to the factorypreset≥Select “Yes” in “Default Settings” in the Setup menu.This returns all values in the Setup menu and the on-screen menu, except for “RemoteControl”, “On-screen Language”, “DVD-Video Ratings” and “BD-Video Ratings” to the defaultsettings.22To return to the factory preset(No setting)≥Reset the unit as follows:1 Press [Í/I] on the unit to turn off the unit.2 Press and hold [9/5], [< OPEN/CLOSE] and [∫] on the unit at the same time formore than 5 seconds until “HELLO” is displayed on the unit.3 The power is turned on and then turned off automatically.—No power. ≥Insert the AC mains lead securely into a household mains socket. 6, 7The unit switches to standbymode.≥One of the unit’s safety devices is activated. Press [Í/I] on the main unit to turn the unit on. —Cannot operate the televisionor receiver.≥Change the manufacturer code. Some televisions or receiver cannot be operated even if youchange the code.≥It may be necessary to set the manufacturer code again after changing the batteries.1010The remote control doesn’twork properly. ≥The remote control and main unit are using different codes.Change the code on the remote control.Press and hold [OK] and the indicated number button at thesame time for more than 5 seconds.≥The batteries are depleted. Replace them with new ones.≥You are not pointing the remote control at the main unit’s remote control signal sensor duringoperation.≥Coloured glass may obstruct the signal reception/transmission.≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlightexposure.≥It may be necessary to set the code on the remote control again after changing the batteries.2955——10, 29The unit is on but cannot beoperated.≥Confirm the correct drive is selected.≥Some operations may be prohibited by the disc.≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.≥One of the unit’s safety devices may have been activated.Reset the unit as follows:1 Press [Í/I] on the main unit to switch the unit to standby.If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about 3seconds. The unit is forcibly switched to standby.Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult thedealer.≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.11—30——Play fails to start even when[1] (PLAY) is pressed.Play starts but then stopsimmediately.≥Insert the disc correctly with the label facing up.≥The disc is dirty.≥You tried to play a blank disc or unplayable disc on this unit.≥[DivX] If playing DivX VOD content, refer to the homepage where you purchased it.11304, 516Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [;] and [9/5] on themain unit at the same time for about 5 seconds. Remove the disc and consult the dealer.—Startup is slow.When the unit is turned on,audio and video output takes along time.It takes time before play starts.≥Startup takes time in the following situations.– Immediately after a power failure or the AC mains lead is connected.– When the unit is connected with an HDMI cable.≥[DivX] This is normal on DivX video.——Cannot set “On” in “BD-Video24p Output”.≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p can you select“On”. In some cases where the unit is connected to a TV via an amplifier/receiver through theHDMI terminals, you may not be able to select “On”. In this case, connect the unit to a TVthrough the HDMI terminal and connect it to the amplifier/receiver through any terminal otherthan HDMI.24The display is dim. ≥Change “FL Display” in the Setup menu. 24The elapsed time displayed isactually less than the playtime.≥The displayed play time is converted from the number of frames at 29.97 frames (equal to0.999 seconds) to one second. There will be a slight difference between the time displayedand the actual elapsed time (e.g., actual one-hour elapsed time may display asapproximately 59 minutes 56 seconds).—DRReference