Panasonic DMR-BWT800 Operating Instructions Manual
Also see for DMR-BWT700: Operating instructions
                                                                                                                        | |
Contents
| 
TroubleshootingVQT3C1496Troubleshooting guideBefore requesting service, make the following checks. Ifthe problem still persists, consult your dealer forinstructions.Updating to the latest software (firmware) may solve theproblem. (> 92)∫ The unit doesn’t work.One of the unit’s safety devices may have beenactivated.Reset the unit as follows:1 Press [Í/I] on the main unit to switch the unit tostandby.≥If the unit doesn’t switch to standby, press [Í/I] onthe main unit for about 3 seconds. The unit isforcibly switched to standby.Alternatively, disconnect the AC mains lead, waitone minute, then reconnect it.2 Press [Í/I] on the main unit to switch it on. If the unitstill cannot be operated, consult the dealer.∫ Cannot eject a disc.The unit may have a problem. While the unit is off, pressand hold [STOP ∫] and [CH W] on the main unit at thesame time for about 5 seconds.The unit is turned off automatically.¾ If you connected this unit to a “HDAVI Control”compatible TV with an HDMI cable, this unit will beautomatically set to standby mode when the TV is set tostandby mode.The display is dim.¾ Change “Unit’s Display”. (> 85)“0:00” is flashing on the unit’s display.¾ Set the clock. (> 90)The time recorded on the disc and theavailable time shown do not add up.¾ If you record or edit about 200 times or more, theremaining capacity of DVD-R, DVD-R DL, +R, and+R DL is reduced and then recording or editing may bedisabled (for the second layer on DVD-R DL and +R DL,this happens after about 60 times).¾ While searching, the elapsed time may not displaycorrectly.¾ Available disc space display may be different from actual.Varying may be large especially when recorded in DRmode.The clock does not display on the unit whenswitched to standby.¾ The clock does not display when “Power Save inStandby” is activated. Ensure “Power Save in Standby” isset to “Off”. (> 89)Screen size is wrong.¾ Check the “TV Aspect” or “Aspect for 4:3 Video”. (> 85)¾ Adjust the aspect ratio setting on TV. Refer to your TV’soperating instructions.¾ If the 16:9 aspect ratio image is output to a 4:3 TV andthe image will be stretched vertically, set “TV Aspect” to4:3. (> 85)¾ Check “Aspect for Recording” before recording or fileconversion. (> 82)¾ If you connect to 4:3 TV, set “HDMI Video Format” to“576p/480p”. (> 86)Pictures do not appear with the HD qualityalthough HD setting was made.¾ The pictures are output with 576p/480p depending on theprogramme.The screen changes automatically.¾ If there is no operation for 5 minutes or more, thedisplayed screen switches to the other statesautomatically (only when the “Screen Saver” is set to“On”). (> 85)The following do not indicate a problem with this unit:≥Regular disc rotating sounds or louder rotating soundswhen recording or high speed copying.≥Poor reception due to atmospheric conditions.≥Image disturbance during search.≥Image disturbance when replacing 3D discs.≥Interruptions in reception due to periodic terrestrialbroadcasting breaks.≥When the unit is turned on or off, there may be anunexpected sound. This does not indicate a problemwith this unit.PowerDisplaysTV screen and video |
Related manuals for Panasonic DMR-BWT700
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine